REFERENCES
- Chakravorty , R. ; Gauri , S.K. ; Chakraborty , S. Optimization of correlated responses of EDM process . Materials and Manufacturing Processes 2011 , 27 , 337 – 347 .
- Lee , S.H. ; Li , X.P. Study of the effect of machining parameters on the machining characteristics in electrical discharge machining of tungsten carbide . Journal of Materials Processing Technology 2001 , 115 ( 3 ), 344 – 358 .
- Singh , S. ; Maheshwari , S. ; Pandey , P.C. Some investigations into the electric discharge machining of hardened tool steel using different electrode materials . Journal of Materials Processing Technology 2004 , 149 ( 1–3 ), 272 – 277 .
- Jahan , M.P. ; Wong , Y.S. ; Rahman , M. A study on the fine-finish die-sinking micro-EDM of tungsten carbide using different electrode materials . Journal of Materials Processing Technology 2009 , 209 ( 8 ), 3956 – 3967 .
- Amorima , F. ; Weingaertner , W. The behavior of graphite and copper electrodes on the finish die-sinking Electrical Discharge Machining (EDM) of AISI P20 tool steel . Journal of the Brazilian Society of Mechanical Sciences and Engineering 2007 , 29 , 367 – 371 .
- Amorima , F. ; Weingaertner , W. The influence of generator actuation mode and process parameters on the performance of finish EDM of a tool steel . Journal of Materials Processing Technology 2005 , 166 , 411 – 416 .
- Kiyak , M. ; Cakir , O. Examination of machining parameters on surface roughness in EDM of tool steel . Journal of Materials Processing Technology 2007 , 191 ( 1–3 ), 141 – 144 .
- Joshi , S.N. ; Pande , S.S. Intelligent process modeling and optimization of die-sinking electric discharge machining . Applied Soft Computing Journal 2011 , 11 ( 2 ), 2743 – 2755 .
- Muthuramalingam , R.T. ; Mohan , B. Influence of tool electrode properties on machinability in spark erosion machining . Materials and Manufacturing Processes 2013 , 28 , 939 – 943 .
- Kumar , S. ; Singh , T.P. A comparative study of the performance of different EDM electrode materials in two dielectric media . Journal of Institute of Engineers India-PR 2007 , 87 , 3 – 8 .
- Rajendran , S. ; Marimuthu , K. ; Sakthivel , M. Study of crack formation and resolidified layer in EDM process on T90Mn2W50Cr45 tool steel . Materials and Manufacturing Processes 2013 , 28 , 664 – 669 .
- Lee , H.T. ; Tai , T.Y. Relationship between EDM parameters and surface crack formation . Journal of Materials Processing Technology 2003 , 142 , 676 – 683 .
- Mohanty , A. ; Talla , G. ; Gangopadhyay , S. Experimental investigation and analysis of EDM characteristics of Inconel 825. Materials and Manufacturing Processes, 2014, 29, 540–549.
- Bhattacharyya , B. ; Gangopadhyay , S. ; Sarkar , B.R. Modelling and analysis of EDMed job surface integrity . Journal of Materials Processing Technology 2007 , 189 ( 1–3 ), 169 – 177 .
- Murray , J.W. ; Clare , A.T. Repair of EDM induced surface cracks by pulsed electron beam irradiation . Journal of Materials Processing Technology 2012 , 212 ( 12 ), 2642 – 2651 .
- Choudhary , R. ; Kumar , H. ; Garg , R.K. Analysis and evaluation of hear affected zone in electric discharge machining EN-31 die steel . Indian Journal of Engineering and Materials Science 2010 , 17 , 91 – 98 .
- Hascalik , A. ; Caydas , U. Electrical discharge machining of titanium alloy (Ti-6Al-4V) . Applied Surface Science 2007 , 253 , 9007 – 9016 .
- Pradhan , M.K. Estimating the effect of process parameters on surface integrity of EDMed AISI D2 tool steel by response surface methodology coupled with grey relational analysis . International Journal of Advanced Manufacturing Technology 2013 , 67 ( 9–12 ), 2051 – 2062 .
- Present address of C. K. Biswas is Department of Petroleum Engineering, Universiti Teknologi Petronas, Malaysia. Color versions of one or more of the figures in the article can be found online at www.tandfonline.com/lmmp.