References
- X. H. Lu et al., A surface roughness prediction model using response surface methodology in micro-milling Inconel 718. IJMMM Mater. 19 (3), 230 (2017). DOI: 10.1504/IJMMM.2017.084006.
- W. Grzesik et al., Investigation of tool wear in the turning of Inconel 718 superalloy in terms of process performance and productivity enhancement. Tribol. Int. 118, 337 (2018). DOI: 10.1016/j.triboint.2017.10.005.
- B. Kursuncu et al., Improvement of cutting performance of carbide cutting tools in milling of the Inconel 718 superalloy using multilayer nanocomposite hard coating and cryogenic heat treatment. Int. J. Adv. Manuf. Technol. 97 (1–4), 467 (2018). DOI: 10.1007/s00170-018-1931-z.
- W. J. Zhang, Study on fluctuation of cutting force in process of high-speed milling of Inconel 718. IJMMM Mater. 18 (5/6), 606 (2016). DOI: 10.1504/IJMMM.2016.078975.
- Z. L. Fang, and T. Obikawa, Turning of Inconel 718 using inserts with cooling channels under high pressure jet coolant assistance. J. Mater. Process. Tech. 247, 19 (2017). DOI: 10.1016/j.jmatprotec.2017.03.032.
- L. B. Li et al., Experimental study of the wear behavior of PCBN inserts during cutting of GH4169 superalloys under high-pressure cooling. Int. J. Adv. Manuf. Technol. 95 (5–8), 1941 (2018). DOI: 10.1007/s00170-017-1333-7.
- Y. Kaynak et al., A comparison of flood cooling, minimum quantity lubrication and high pressure coolant on machining and surface integrity of titanium Ti-5553 alloy. J. Manuf. Process. 34, 503 (2018). DOI: 10.1016/j.jmapro.2018.06.003.
- M. Sadeghifar et al., A comprehensive review of finite element modeling of orthogonal machining process: Chip formation and surface integrity predictions. Int. J. Adv. Manuf. Technol. 96 (9–12), 3747 (2018). DOI: 10.1007/s00170-018-1759-6.
- R. K. Yadav, K. Abhishek, and S. S. Mahapatra, A simulation approach for estimating flank wear and material removal rate in turning of Inconel 718. Simul. Model. Pract. Th. 52, 1 (2015). DOI: 10.1016/j.simpat.2014.12.004.
- G. M. Pittala, and M. Monno, 3D finite element modeling of face milling of continuous chip material. Int. J. Adv. Manuf. Technol. 47, 543 (2010). DOI: 10.1007/s00170-009-2235-0.
- C. Ezilarasan, V. S. Senthil kumar, and A. Velayudham, Theoretical predictions and experimental validations on machining the Nimonic C-263 super alloy. Simul. Model. Pract. Th. 40, 192 (2014). DOI: 10.1016/j.simpat.2013.09.008.
- A. H. Jaafar, and H. Al-Ethari, Optimisation of machining Ti6Al4V alloy: Numerical simulation and experimental verification. IJMMM Mater. 20 (5), 447 (2018). DOI: 10.1504/IJMMM.2018.10017193.
- H. J. Hu, W. J. Huang, and G. S. Wu, 3D finite element modelling and experimental researches on turning steel AISI1013 by nano-crystalline Al2O3 ceramics cutter. IJMMM Mater. 14 (3), 295 (2013). DOI: 10.1504/IJMMM.2013.056369.
- A. Qasim et al., Optimization of process parameters for machining of AISI-1045 steel using Taguchi design and ANOVA. Simul. Model. Pract. Th. 59, 36 (2015). DOI: 10.1016/j.simpat.2015.08.004.
- J. F. Ma, N. H. Duong, and S. T. Lei, 3D numerical investigation of the performance of microgroove textured cutting tool in dry machining of Ti-6Al-4V. Int. J. Adv. Manuf. Technol. 79 (5–8), 1313 (2015). DOI: 10.1007/s00170-015-6937-1.
- A. Malakizadi et al., Influence of friction models on FE simulation results of orthogonal cutting process. Int. J. Adv. Manuf. Technol. 88 (9–12), 3217 (2017). DOI: 10.1007/s00170-016-9023-4.
- V. Kalhori, D. Wedberg, and L. E. Lindgren, Simulation of mechanical cutting using a physical based material model. Int. J. Mater. Form. 3 (S1), 511 (2010). DOI: 10.1007/s12289-010-0819-8.
- C. Liu et al., Study on surface defects in milling Inconel 718 super alloy. J. Mech. Sci. Technol. 29 (4), 1723 (2015). DOI: 10.1007/s12206-015-0345-1.
- J. M. Zhou et al., Study of surface quality in high speed turning of Inconel 718 with uncoated and coated CBN tools. Int. J. Adv. Manuf. Technol. 58 (1–4), 141 (2012).