References
- H. Tanaka, T. Sugihara, and T. Enomoto, High speed machining of Inconel 718 focusing on wear behaviors of pcbn cutting tool, Procedia CIRP. 46, 545 (2016). DOI: https://doi.org/10.1016/j.procir.2016.03.120.
- F. Jafarian et al., Finite element simulation of machining Inconel 718 alloy including microstructure changes, Int J Mech Sci 88, 110 (2014). DOI: https://doi.org/10.1016/j.ijmecsci.2014.08.007.
- A. Mama, B. Aia, and A. Anmk, Specific cutting energy of Inconel 718 under dry, chilled-air and minimal quantity nanolubricants - ScienceDirect, Procedia CIRP 77, 429 (2018).
- Y. Hua, and Z. Liu, Effects of cutting parameters and tool nose radius on surface roughness and work hardening during dry turning Inconel 718, Int. J. Adv. Manuf. Technol. 96 (5–8), 2421 (2018). DOI: https://doi.org/10.1007/s00170-018-1721-7.
- X. Ren, and Z. Liu, Influence of cutting parameters on work hardening behavior of surface layer during turning superalloy Inconel 718, Int. J. Adv. Manuf. Technol. 86 (5-8), 2319 (2016). DOI: https://doi.org/10.1007/s00170-016-8350-9.
- R. Arunachalam, and M. Mannan, A: Machinability of nickel-based high temperature alloys, Mach. Sci. Technol. 4 (1), 127 (2000). DOI: https://doi.org/10.1080/10940340008945703.
- A. M. Adaskin, A. A. Vereshchaka, and A. S. Vereshchaka, Study of wear mechanism of hard-alloy tools during machining of refractory alloys, J. Frict. Wear. 34 (3), 208 (2013). DOI: https://doi.org/10.3103/S1068366613030021.
- A. Maryam, M. Saharnaz, and S. C. Veldhuis, A novel treatment for cutting tools for reducing the chipping and improving tool life during machining of Inconel 718, Wear 414–415, 79 (2018). DOI: https://doi.org/10.1016/j.wear.2018.08.002.
- E. O. Ezugwu, and J. Bonney, Effect of high-pressure coolant supplies when machining nickel-base, Inconel 718, alloy with ceramic tools, Tribol. Trans. 46 (4), 580 (2003). DOI: https://doi.org/10.1080/10402000308982667.
- A. R. Machado, and J. Wallbank, Effects of a high-pressure coolant jet on machining, Proc. Inst. Mech. Eng. Part B-J. Eng. Manuf. 208 (1), 29 (1994). DOI: https://doi.org/10.1243/PIME_PROC_1994_208_057_02.
- J. Kaminski et al., Control of chip flow direction in high-pressure water jet-assisted orthogonal tube turning, Proc. Inst. Mech. Eng. Part B-J. Eng. Manuf. 214 (7), 529 (2000). DOI: https://doi.org/10.1243/0954405001518224.
- C. Shet, X. Deng, and A. E. Bayoumi, Finite element simulation of high-pressure water-jet assisted metal cutting, Int. J. Mech. Sci. 45 (6–7), 1201 (2003). DOI: https://doi.org/10.1016/S0020-7403(03)00142-5.
- M. Vosough et al., Influence of high pressure water-jet assisted turning on surface residual stresses on Ti-6AL-4V alloy by measurement and finite element simulation. Proceedings of SPIE - The International Society for Optical Engineering2015. 5852.
- M. Mazurkiewicz, A manufacturing tool for a new century, J. Mater. Process. Tech. 106 (1–3), 112 (2000). DOI: https://doi.org/10.1016/S0924-0136(00)00600-2.
- Y. Y. Lei, and X. Z. Tao, Water Jet Technology and Engineering Application (Chemical Industry Press, Beijing 2017).
- J. Q. Zhou, X. Ai, and C. Z. Huang, A new model for calculating tool-chip contact length, J. Shandong Univ. Technol. 28, 44 (1998).
- HPC calculator: How to use high-pressure coolant and optimize calculations, Sandvik. [DB/OL]. http://www.sandvik.coromant.com/zhcn/knowledge/calculators_and_software/high_pressure_coolant/.