References
- X. Liu et al., Research on the technical progress of milling for hardened steel mould of automotive covering parts, JME 52 (17), 035 (2016). DOI: https://doi.org/10.3901/JME.2016.17.035.
- B. U. Guzel, and L. Lazoglu, An enhanced force model for sculptured surface maching, Mach. Sci. Technol. 8 (3), 431 (2004). DOI: https://doi.org/10.1081/MST-200040596.
- C. Sim, and M. Y. Yang, The prediction of the cutting force in ball-end milling with a flexible cutter, Int. J. Mach. Tools Manuf. 33 (2), 267 (1993). DOI: https://doi.org/10.1016/0890-6955(93)90079-A.
- J. J. J. Wang, and C. Y. Huang, A force-model-based approach to estimating cutter axis offset in ball end milling, Int. J. Adv. Manuf. Technol. 24 (11–12), 910 (2004). DOI: https://doi.org/10.1007/s00170-003-1822-8.
- K. Zhu, and Y. Zhang, Modeling of the instantaneous milling force per tooth with tool run-out effect in high speed ball-end milling, Int. J. Mach. Tools Manuf. 118–119, 37 (2017). DOI: https://doi.org/10.1016/j.ijmachtools.2017.04.001.
- L. Zhu, and C. Liu, Recent progress of chatter prediction, detection and suppression in milling, Mech. Syst. Signal Process. 143, 106840 (2020). DOI: https://doi.org/10.1016/j.ymssp.2020.106840.
- C. Liu, L. Zhu, and C. Ni, Chatter detection in milling process based on VMD and energy entropy, Mech. Syst. Signal Process. 105, 169 (2018). DOI: https://doi.org/10.1016/j.ymssp.2017.11.046.
- X. Zhang et al., Tool orientation optimization of 5-axis ball-end milling based on an accurate cutter/workpiece engagement model, CIRP J. Manuf. Sci. Technol. 19, 106 (2017). DOI: https://doi.org/10.1016/j.cirpj.2017.06.003.
- S. Lotfi et al., An approach to modeling the chip thickness and cutter workpiece engagement region in 3 and 5 axis ball end milling, J. Manuf. Processes 34, 7 (2018).
- R. Yan et al., Three degrees of freedom stability analysis in the milling with bull-nosed end mills, Int. J. Adv. Manuf. Technol. 86 (1-4), 71 (2016). DOI: https://doi.org/10.1007/s00170-015-8144-5.
- Z. Zhu et al., Parametric chip thickness model based cutting forces estimation considering cutter runout of five-axis general end milling, Int. J. Mach. Tools Manuf. 101, 35 (2016). DOI: https://doi.org/10.1016/j.ijmachtools.2015.11.001.
- M. Wan, and W. H. Zhang, Systematic study on cutting force modelling methods for peripheral milling, Int. J. Mach. Tools Manuf. 49 (5), 424 (2009). DOI: https://doi.org/10.1016/j.ijmachtools.2008.12.004.
- M. Wan et al., New procedures for calibration of instantaneous cutting force coefficients and cutter runout parameters in peripheral milling, Int. J. Mach. Tools Manuf. 49 (14), 1144 (2009). DOI: https://doi.org/10.1016/j.ijmachtools.2009.08.005.
- W. Donghui et al., Numerical simulation on ball end milling harden steel assembled with different hardness, J. Harbin Univ. Sci. Technol. 16 (5), 16 (2011).
- W. Yangyu, et al., Investigation on vibration of ball end milling harden steel assembled with different hardness, China Mech. Eng. 23 (6), 10 (2012).
- M. A. Davies, and B. Balachandran, Impact dynamics in milling of thin-walled structures, Nonlinear Dyn. 22 (4), 375 (2000). DOI: https://doi.org/10.1023/A:1008364405411.
- L. LIfu, T. Shengang, and H. Shutao, Study on effect of impact force on feed mode for milling titanium alloy, J. Tool Engineering 51 (10), 54 (2017).
- G. Stepan, T. Insperger, and R. Szalai, Nonlinear dynamics of high-speed milling, International Congress of Theoretical and Applied Mechanics, 2015.
- X. An, and P. Shangfeng et al., Analysis of contact model in multi-body system dynamic simulation, J. Comput. Simulat. 25 (10), 98 (2008).
- H. M. Lankarani, and P. E. Nikravesh, A contact force model with hysteresis damping for impact analysis of multibody systems, J. Mech. Des. 112 (3), 369 (1990). DOI: https://doi.org/10.1115/1.2912617.
- H. M. Lankarani, and P. E. Nikravesh, Continuous contact force models for impact analysis in multibody systems, Nonlin. Dynamics 5 (2), 193, (1994).
- P. Lee, and Y. Altintas, Prediction of ball-end milling forces from orthogonal cutting data, Int. J. Mach. Tools Manuf. 36 (9), 1059 (1996). DOI: https://doi.org/10.1016/0890-6955(95)00081-X.