References
- Peyre P, Scherpereel X, Berthe L, et al. Surface modifications induced in 316L steel by laser peening and shot-peening. Influence on pitting corrosion resistance. Mater Sci Eng A. 2000;280(2):294–302.
- Xu Z-D, Wang K-Y, Guo Y-Q, et al. Hybrid test on building structures using electrodynamic fatigue test machine. Nondestr Test Eval. 2017;32(1):90–102.
- Kumar J, Ahmad S, Mukhopadhyay CK, et al. Acoustic emission studies for characterization of fatigue crack growth behavior in HSLA steel. Nondestr Test Eval. 2016;31(1):77–96.
- Luo Q, Jones AH. High-precision determination of residual stress of polycrystalline coatings using optimised XRD-sin2ψ technique. Surf Coat Technol. 2010;205(5):1403–1408.
- Angerer P, Strobl S. Equi-penetration grazing incidence X-ray diffraction method: stress depth profiling of ground silicon nitride. Acta Materialia. 2014;77:370–378.
- Baczmanski A, Lark RJ, Skrzypek SJ. Application of non-linear sin2ψ method for stress determination using x-ray diffraction. Mater Sci Forum. 2002;404–407:29–34.
- Bolelli G, Lusvarghi L, Varis T, et al. Residual stresses in HVOF-sprayed ceramic coatings. Surf Coat Technol. 2008;202(19):4810–4819.
- Chang J-Y, Yu G-P, Huang J-H. Determination of Young’s modulus and Poisson’s ratio of thin films by combining sin2ψ X-ray diffraction and laser curvature methods. Thin Solid Films. 2009;517(24):6759–6766.
- Genzel C. Formalism for the evaluation of strongly non-linear surface stress fields by X-ray diffraction performed in the scattering vector mode. Phys Status Solidi A. 1994;146(2):629–637.
- Sattonnay G, Lahrichi M, Herbst-Ghysel M, et al. Stress field induced by swift heavy ion irradiation in cubic yttria stabilized zirconia. J Appl Phys. 2007;101(10):103516.
- Tanaka K, Akiniwa Y, Suzuki K, et al. High-energy x-ray synchrotron radiation analysis of residual-stress distribution of shot-peened steel. Mater Sci Forum. 2002;404–407:341–348.
- Tang W, Deng L, Xu K, et al. X-ray diffraction measurement of residual stress and crystal orientation in Au/NiCr/Ta films prepared by plating. Surf Coat Technol. 2007;201(12):5944–5947.
- Wang A-N, Chuang C-P, Yu G-P, et al. Determination of average X-ray strain (AXS) on TiN hard coatings using cos 2 αsin 2 ψ X-ray diffraction method. Surf Coat Technol. 2015;262:40–47.
- Wu H, Peng H, Li X, et al. Effect of hydrogen addition on diffusion bonding behavior of Ti-55 alloy. Mater Sci Eng A. 2019;739:244–253.
- Zoei MS, Sadeghi MH, Salehi M. High-precision determination of residual stress of as-sprayed and ground WC-10Co-4Cr coating using optimized XRD-sin2ψ technique. Key Eng Mater. 2017;748:381–385.
- Belassel M, Pineault J, Brauss M. Residual stress measurements inside a small inner diameter hole at low bragg angle using x-ray diffraction technique. Mater Res Proc. 2017;2:37–42.
- Zhang Y-L, Liu Z-M, Liu J-M. The x-ray diffraction characteristics of different materials. Mater Sci Forum. 2010;638–642:2434–2439.
- Munsi A, Waddell AJ, Walker CA. A method for determining X-ray elastic constants for the measurement of residual stress. Strain. 2003;39:3–10.
- Szymanski W, Lech-Grega M. Validation of the x-ray stress measurement method. Adv Mater Sci. 2014;14:102–109.
- Pencea I, Tiriba G. Multiconvolutional approach for uncertainty estimation of the residual stresses measured by XRD sin2ψ method. Univ Politehnica Buchar Sci Bull Ser A. 2013;75(4):275–284.