Tool wear and chip analysis after the hard turning of AISI D6 steel assisted by LN₂

References

• Arsecularatne, J.A.; Zhang, L.C.; Montross, C.; Mathew, P. (2006) On machining of hardened AISI D2 steel with PCBN tools. Journal of Materials Processing Technology, 171: 244–252.
   Web of Science ®Google Scholar
• Bermingham, M.J.; Kirsh, J.; Sun, S.; Palanisamy, S.; Dargusch, M.S. (2011) New observations on tool life, cutting forces and chip morphology in cryogenic machining Ti-6Al-4V. International Journal of Machine Tools and Manufacture, 51: 500–511.
   Web of Science ®Google Scholar
• Bicek, M.; Doumont, F.; Courbon, C.; Pusavec, F.; Rech, J.; Kopac, J. (2012) Cryogenic machining as an alternative turning process of normalized and hardened AISI 52100 bearing steel. Journal of Materials Processing Technology, 212: 2609–2618.
   Web of Science ®Google Scholar
• Bonfá, M.M. (2013) Torneamento do aço endurecido AISI D6 utilizando mínima quantidade de fluido de corte (Hard turning of AISI D6 steel using MQL). MSc thesis, Federal University of Uberlândia, Uberlândia/MG, Brazil.
   Google Scholar
• Bordin, A.; Sartori, S.; Bruschi, S.; Ghiotti, A. (2017) Experimental investigation on the feasibility of dry and cryogenic machining as sustainable strategies when turning Ti6Al4V produced by additive manufacturing. Journal of Cleaner Production, 142: 4142–4151.
   Web of Science ®Google Scholar
• Dolinsek, S.; Ekinovic, S.; Kopac, J. (2004) A contribution to the understanding of chip formation mechanism in high-speed cutting of hardened steel. Journal of Materials Processing Technology, 157–158: 485–490.
   Web of Science ®Google Scholar
• Jawahir, I.S.; Attia, H.; Biermann, D.; Duflou, J.; Klocke, F.; Meyer, D.; Newman, S.T.; Pusavec, F.; Putz, M.; Rech, J.; Schule, V.; Umbrello, D. (2016) Cryogenic manufacturing processes. CIRP Annals – Manufacturing Technology, 65: 713–736.
   Web of Science ®Google Scholar
• Kaynak, Y.; Karaca, H.E.; Jawahir, I.S. (2015) Cutting speed dependent microstructure and transformation behavior of NiTi alloy in dry and cryogenic machining. Journal of Materials Engineering and Performance, 24(1): 452–460.
   Web of Science ®Google Scholar
• Kaynak, Y. (2014) Evaluation of machining performance in cryogenic machining of Inconel 718 and comparison with dry and MQL machining. International Journal of Advanced Manufacturing Technology, 72: 919–933.
   Web of Science ®Google Scholar
• Klocke, F.; Lung, D.; Arft, M.; Priarone, P.C.; Settineri, L. (2013) On high-speed turning of a third-generation gamma titanium aluminide. International Journal of Advanced Manufacturing Technology, 64: 155–163.
   Google Scholar
• Leadebal, W.V.; Melo, A.C.A.; Oliveira, A.J.; Castro, N.A. (2018) Effects of cryogenic cooling on the surface integrity in hard turning of AISI D6 steel. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 40: 15.
   Web of Science ®Google Scholar
• Nayak, M.; Sehgal, R. (2015) Effect of tool material properties and cutting conditions on machinability of AISI D6 steel during hard turning. Arabian Journal for Science and Engineering, 40: 1151–1164.
   Web of Science ®Google Scholar
• Oliveira, A.J.; Boing, D.; Schroeter, R.B. (2016) Effect of PCBN tool grade and cutting type on hard turning of high-chromium white cast iron. The International Journal of Advanced Manufacturing Technology, 82: 797–807.
   Web of Science ®Google Scholar
• Priarone, P.C.; Klocke, F.; Faga, M.G.; Lung, D.; Settineri, L. (2016) Tool life and surface integrity when turning titanium aluminides with PCD tools under conventional wet cutting and cryogenic cooling. International Journal of Advanced Manufacturing Technology, 85: 807–816.
   Web of Science ®Google Scholar
• Pusavec, F.; Deshpande, A.; Yang, S.; M’saoubi, R.; Kopac, J.; Dillon Jr., O.W.; Jawahir, I.S. (2014) Sustainable machining of high temperature nickel alloy – Inconel 718: part 1 – predictive performance models. Journal of Cleaner Production, 81: 225–269.
   Web of Science ®Google Scholar
• Sandvik. (2017) Hard part turning with CBN. The PDF catalogue. Available: http://www.sandvik.coromant.com/…/catalogues/en-gb/c-2940-137.pdf
   Google Scholar
• Scandiffio, I.; Diniz, A.E.; De Souza, A.F. (2016) Evaluating surface roughness, tool life, and machining force when milling free-form shapes on hardened AISI D6 steel. The International Journal of Advanced Manufacturing Technology, 82: 2075–2086.
   Web of Science ®Google Scholar
• Shokrani, A.; Dhokia, V.; Newman, S.T. (2012) Environmentally conscious machining of difficult-to-machine materials with regard to cutting fluids. International Journal of Machine Tools & Manufacture, 57: 83–101.
   Web of Science ®Google Scholar
• Thiele, J.D.; Melkote, S.N. (1999) Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel. Journal of Materials Processing Technology, 94: 216–226.
   Web of Science ®Google Scholar
• Trent, E. M; Wright, P.K. (2000) Metal Cutting. 4th ed. Butterworth-Heinemann, Boston, 446p.
   Google Scholar
• Umbrello, D.; Micari, F.; Jawahir, I.S. (2012) The effects of cryogenic cooling on surface integrity in hard machining: a comparison with dry machining. CIRP Annals – Manufacturing Technology, 61: 103–106.
   Web of Science ®Google Scholar
• Xavier, S.E.D.; Delijaicov, S.; De Farias, A. (2011) Investigation on the surface integrity and tool wear in cryogenic machining. Int. Conf. Adv. Mater. Process. Technol., 1199–1204.
   Google Scholar