Method for reducing aluminum alloy heat loss in high pressure die casting shot sleeves

References

• Gunasegaram DR, Finnin BR, Polivka FB. Melt flow velocity in high pressure die casting: its effect on microstructure and mechanical properties in an Al–Si alloy. Mater. Sci. Technol. 2007;23:847–856.10.1179/174328407X176992
   Web of Science ®Google Scholar
• Han T-H, Kuo J-H, Hwang W-S. Numerical simulation of the liquid-gas interface shape in the shot sleeve of cold chamber die casting machine. J. Mater. Eng. Perform. 2007;16:521–526.10.1007/s11665-007-9093-4
   Web of Science ®Google Scholar
• Kato H, Suzuki T, Annou Y, et al. Nondestructive detection of cold flakes in aluminum alloy die-cast plate with ultrasonic measurement. Mater Trans. 2004;45:2403–2409.10.2320/matertrans.45.2403
   Web of Science ®Google Scholar
• Kato H, Suzuki T, Annou Y, et al. Nondestructive detection of cold flakes in aluminum alloy die-cast plate with ultrasonic measurement. Mater Trans. 2004;45:2403–2409.10.2320/matertrans.45.2403
   Web of Science ®Google Scholar
• Helenius R, Lohne O, Arnberg L, et al. The heat transfer during filling of a high-pressure die-casting shot sleeve. Mater Sci Eng A. 2005;413–414:52–55.10.1016/j.msea.2005.08.166
   Web of Science ®Google Scholar
• Lee JH, Kim HS, Won CW, et al. Effect of the gap distance on the cooling behavior and the microstructure of indirect squeeze cast and gravity die cast 5083 wrought Al alloy. Mater Sci Eng. 2002;338:182–190.10.1016/S0921-5093(02)00054-0
   Google Scholar
• Iwahori H, Tozawa K, Asano T, et al. Properties of scattered structures included in aluminum die castings. J Jpn Inst Light Met. 1984;34:525–530. [Japanese].10.2464/jilm.34.525
   Google Scholar
• Verran GO, Mendes RPK, Rossi MA. Influence of injection parameters on defects formation in die casting Al12Si1,3Cu alloy: Experimental results and numeric simulation. J Mater Proc Technol. 2006;179:190–195.10.1016/j.jmatprotec.2006.03.089
   Web of Science ®Google Scholar
• Aoyama S, Tashiro M, Sakamoto K, et al. Quality improvement of aluminum alloy die castings by powder lubricant for shot sleeve. Jpn Foundry Eng Soc. 1992;64:684–692.
   Google Scholar
• Hamasaiid A, Dour G, Dargusch MS, et al. Heat-transfer coefficient and in-cavity pressure at the casting-die interface during high-pressure die casting of the magnesium alloy AZ91D. Metal Mater Trans A. 2008;39:853–864.10.1007/s11661-007-9452-7
   Web of Science ®Google Scholar
• Loulou T, Artyukhin EA, Bardon JP. Estimation of thermal contract resistance during the first stages of metal solidification process: II-experimental setup and results. Int J Heat Mass Trans. 1999;42:2129–2142.10.1016/S0017-9310(98)00338-X
   Web of Science ®Google Scholar
• Vinith S, Uthayakumar A, Rajan SS, et al. Fluidity of ADC12 alloy based on theoretical and computational fluid dynamics. Int J Sci Research. 2015;4:996–999.
   Google Scholar
• Vreeman CJ, Incropera FP. The effect of free-floating dendrites and convection on macrosegregation in direct chill cast aluminum alloys: part II: predictions for Al-Cu and Al–Mg alloys. Int J Heat Mass Trans. 2000;43:687–704.10.1016/S0017-9310(99)00175-1
   Web of Science ®Google Scholar
• YuQing W, YuQin W, WiuFang B. Composition dependence of viscosity for Al(1-x)Mgx(0≤ x≤0.10) alloys. Chinese Sci Bulletin. 2007;52:1441–1445.
   Google Scholar
• Sabatino MD, Arnberg L. A review on the fluidity of Al based alloys. Matell Sci Tech. 2013;22:9–15.
   Google Scholar
• Zhu BW, Li LX, Liu X, et al. Effect of viscosity measurement method to simulate high pressure die casting of thin-wall AlSi10MnMg alloy castings. J. Mater. Eng. Perform. 2015;24:5032–5036.10.1007/s11665-015-1783-8
   Web of Science ®Google Scholar
• Kobatake H, Brillo J, Schmitz J, et al. Surface tension of binary Al–Si liquid alloys. J Mater Sci. 2015;50:3351–3360.10.1007/s10853-015-8883-6
   Web of Science ®Google Scholar
• Cordovilla CG, Louis E, Pamies A. The surface tension of liquid pure aluminum and aluminum-magnesium alloy. J Mater Sci. 1986;21:2787–2792.10.1007/BF00551490
   Web of Science ®Google Scholar
• Lee J, Shimoda W, Tanaka T. Surface tension and its temperature coefficient of liquid Sn–X (X=Ag, Cu) alloys. Mater. Trans. 2004;45:2864–2870.10.2320/matertrans.45.2864
   Web of Science ®Google Scholar
• Plevachuk Y, Sklyarchuk V, Gerbeth G, et al. Surface tension and density of liquid Bi–Pb, Bi–Sn and Bi–Pb–Sn eutectic alloys. Surface Sci. 2011;605:1034–1042.10.1016/j.susc.2011.02.026
   Web of Science ®Google Scholar
• Thresh HR, Crawley AF. The viscosities of lead, tin and Pb–Sn alloys. Metal Trans. 1970;1:1531–1535.10.1007/BF02641997
   Web of Science ®Google Scholar
• Morris CJ. Microscale self-assembled electrical contacts. Adelphi, MD: Army Research Laboratory; Sept. 2007.
   Google Scholar
• Wang X-L, Feygenson M, Aronson MC, et al. Sn/SnOx core–shell nanospheres: synthesis, anode performance in Li ion batteries, and superconductivity. J Phys Chem C. 2010;114:14697–14703.10.1021/jp101852y
   Web of Science ®Google Scholar