References
- Shahzad K, Deckers J, Zhang Z, et al. Additive manufacturing of zirconia parts by indirect selective laser sintering. J Eur Ceram Soc. 2014;34(1):81–89. doi: 10.1016/j.jeurceramsoc.2013.07.023
- Mitra AE, Mehran SH, Sara SS, et al. Structure, properties, and in vitro behavior of heat-treated calcium sulfate scaffolds fabricated by 3D printing. Plos One. doi: 10.1371/journal.pone.0151216
- Ebert J, Ozkol E, Zeichner A, et al. Direct inkjet printing of dental prostheses made of zirconia. J Dent Res. 2009;88(7):673. doi: 10.1177/0022034509339988
- Wang J, Shaw LL, Cameron TB. Solid freeform fabrication of Permanent dental restorations via slurry micro-extrusion. J Am Ceram Soc. 2006;89(1):346–349. doi: 10.1111/j.1551-2916.2005.00672.x
- Dehurtevent M, Robberecht L, Hornez JC, et al. Stereolithography: a new method for processing dental ceramics by additive computer-aided manufacturing. Dent Mater. 2017;33(5):477. doi: 10.1016/j.dental.2017.01.018
- Schwentenwein M, Homa J. Additive manufacturing of dense alumina ceramics. Int J Appl Ceram Tec. 2015;12(1):1–7. doi: 10.1111/ijac.12319
- Rosen DW. Stereolithography and rapid prototyping. In: Hesketh PJ, editor. Bionanofluidic MEMS. MEMS reference shelf. Boston (MA): Springer; 2008. p. 175–196.
- Griffith ML, Halloran JW. Freeform fabrication of ceramics via stereolithography. J Am Ceram Soc. 2010;79(10):2601–2608. doi: 10.1111/j.1151-2916.1996.tb09022.x
- Felzmann R, Gruber S, Mitteramskogler G, et al. Lithography-based additive manufacturing of cellular ceramic structures. Adv Eng Mater. 2012;14(12):1052–1058. doi: 10.1002/adem.201200010
- Chen Z, Li D, Zhou W. Process parameters appraisal of fabricating ceramic parts based on stereolithography using the Taguchi method. P I Mech Eng B-J Eng. 2012;226(7):1249–1258.
- An D, Li H, Xie Z, et al. Additive manufacturing and characterization of complex Al2O3 parts based on a novel stereolithography method. Int J Appl Ceram Tec. doi:10.1111/ijac.12721.
- Mitteramskogler G, Gmeiner R, Felzmann R, et al. Light curing strategies for lithography-based additive manufacturing of customized ceramics. 3D Print Addit Manuf. 2014;s 1–4:110–118.
- Lee CS, Kim SG, Kim HJ, et al. Measurement of anisotropic compressive strength of rapid prototyping parts. J Mater Process Tech. 2007;s 187–188(12):627–630. doi: 10.1016/j.jmatprotec.2006.11.095
- Johansson E, Lidström O, Johansson J, et al. Influence of resin Composition on the defect Formation in Alumina manufactured by stereolithography. Materials (Basel). 2017;10(2):138. doi: 10.3390/ma10020138
- Wu H, Cheng Y, Liu W, et al. Effect of the particle size and the debinding process on the density of alumina ceramics fabricated by 3D printing based on stereolithography. Ceram Int. 2016;42(15):17290–17294. doi: 10.1016/j.ceramint.2016.08.024
- Brady GA, Halloran JW. Stereolithography of ceramic suspensions. Rapid Prototyping J. 1997;3(2):61–65. doi: 10.1108/13552549710176680
- Tomeckova V, Halloran JW. Critical energy for photopolymerization of ceramic suspensions in acrylate monomers. J Eur Ceram Soc. 2010;30(16):3273–3282. doi: 10.1016/j.jeurceramsoc.2010.08.003
- Gentry SP, Halloran JW. Depth and width of cured lines in photopolymerizable ceramic suspensions. J Eur Ceram Soc. 2013;33(10):1981–1988. doi: 10.1016/j.jeurceramsoc.2013.02.033
- Ortmann C, Oberbach T, Richter H, et al. Stereolithography process: influence of the rheology of silica suspensions and of the medium on polymerization kinetics – cured depth and width. J Eur Ceram Soc. 2012;32(8):1625–1634. doi: 10.1016/j.jeurceramsoc.2012.01.010
- Chen Z, Li D, Zhou W. Process parameters appraisal of fabricating ceramic parts based on stereolithography using the Taguchi method. P I Mech Eng B-J Eng. 2012;226(7):1249–1258.
- Taguchi G, Konishi S. Taguchi methods, orthogonal arrays and linear graphs, tools for quality engineering. Dearborn (MI): American Supplier Institute; 1997.
- Gowda RBS, Udayagiri CS, Narendra DD. Studies on the process parameters of rapid prototyping technique (stereolithography) for the betterment of part quality. Int J Manuf Eng. 2014;2014(2):1–11.
- Tian X, Günster J, Melcher J, et al. Process parameters analysis of direct laser sintering and post treatment of porcelain components using Taguchi’s method. J Eur Ceram Soc. 2009;29(10):1903–1915. doi: 10.1016/j.jeurceramsoc.2008.12.002
- Raju BS, Chandra SU, Drakshayani DN. Grey relational analysis coupled with principal component analysis for optimization of stereolithography process to enhance part quality. IOP Conf. Ser: Mater Sci Eng. 2017;225. doi:10.1088/1757-899X/225/1/012228.
- Montgomery DC. Design and analysis of experiments. 6th ed. Hoboken (NJ): Wiley; 2005. doi:10.1198/tech.2006.s372.
- Chen YF, Lin YJ, Lin YC, et al. Optimization of electrodischarge machining parameters on ZrO2 ceramic using the Taguchi method. P I Mech Eng B-J Eng. 2009;224(2):195–205.
- Gowda RBS, Udayagiri CS, Narendra DD. Studies on the process parameters of rapid prototyping technique (stereolithography) for the betterment of part quality. Int J Manuf Eng. 2014;2014(2):1–11.
- Kukielka L. Designating the field areas for the contact of a rotary burnishing element with the rough surface of a part, providing a high-quality product. J Mech Working Tech. 1989;19(3):319–356. doi: 10.1016/0378-3804(89)90081-8
- Iii JWF, Johnson GC, Klein PA, et al. On the toughening of brittle materials by grain bridging: Promoting intergranular fracture through grain angle, strength, and toughness. J Mech Phys Solids. 2008;56(6):2381–2400. doi: 10.1016/j.jmps.2007.12.006