Thin kerf cutting forces of frozen and non-frozen Norway spruce and Scots pine wood

References

• Aknouche, H., Outahyon, A., Nouveau, C., Marchal, R., Zerizer, A. and Butaud, J. C. (2009) Tool wear effect on cutting forces: In routing process of Aleppo Pine wood. Journal of Materials Processing Technology, 209(6), 2918–2922.
   Web of Science ®Google Scholar
• Andrade, A. C. A., Xavier, C. N., Simetti, R. and da Silva, J. (2019) Influence of wood density on the specific cutting force during planning. In Proceedings of the 24th International Wood Machining Seminar, pp. 283–290.
   Google Scholar
• Axelsson, B., Lundberg, Å and Grönlund, A. (1993) Studies of the main cutting force at and near a cutting edge. Holz als Roh- und Werkstoff, 51, 43–48.
   Google Scholar
• Chuchala, D., Orlowski, K. A., Sandak, A., Sandak, J., Pauliny, D. and Barański, J. (2014) The effect of wood provenance and density on cutting forces while sawing Scots pine (Pinus sylvestris L.). BioResources, 9(3), 5349–5361.
   Web of Science ®Google Scholar
• Ekevad, M., Berg, S., Öhman, M. and Guo, X. (2017) Potential yield increase with reduced saw kerf deviations when curve sawing. In Proceedings of the 23rd International Wood Machining Seminar (Gdansk University of Technology), pp. 36–42.
   Google Scholar
• Ekevad, M., Öhman, M. and Guo, X. (2019) Single tooth cutting forces in green Norway Spruce: Experimental results. In Proceedings of the 24th International Wood Machining Seminar (Oregon State University (OSU)), pp. 9–22.
   Google Scholar
• Eyma, F., Méausoone, P. J. and Martin, P. (2004) Study of the properties of thirteen tropical wood species to improve the prediction of cutting forces in mode B. Annals of Forest Science, 61(1), 55–64.
   Web of Science ®Google Scholar
• Franz, N. C. (1958) An Analysis of the Wood-Cutting Process. The Engineering Research Institute, November, p148.
   Google Scholar
• Fredriksson, M. and Svensson, M. (2020) A sawmill simulation study of the volume yield changes when sawing with thinner kerfs. In Proceedings of the 2020 Society of Wood Science and Technology International Convention: Renewable Resources for a Sustainable and Healthy Future (International Society of Wood Science and Technology (SWST)), pp. 363–376.
   Google Scholar
• Hernández, R. E., Passarini, L. and Koubaa, A. (2014) Effects of temperature and moisture content on selected wood mechanical properties involved in the chipping process. Wood Science and Technology, 48(6), 1281–1301.
   Web of Science ®Google Scholar
• Ispas, M. and Campean, M. (2014) Experimental research on sawing frozen wood. Bulletin of the Transilvania University of Brasov. Forestry, Wood Industry, Agricultural Food Engineering. Series II, 7(1), 51.
   Google Scholar
• Kivimaa, E. (1950) Cutting Forces in Wood Working (Helsinki: Julkaisu/Valtion teknillinen tutkimuslaitos).
   Google Scholar
• Kollmann, F. F. and Cote, W. A. (1968) Principles of Wood Science and Technology: I Solid Wood (Berlin: Springer).
   Google Scholar
• Kubler, H., Liang, L. and Chang, L. (2007) Thermal expansion of moist wood. Wood and Fiber Science, 5(3), 257–267.
   Google Scholar
• Lestander, D. (2011) Competition for forest fuels in Sweden – Exploring the possibilities of modeling forest fuel markets in a regional partial equilibrium framework. Master Thesis, Swedish University of Agricultural Sciences, Uppsala, Sweden.
   Google Scholar
• Lhate, I., Cristóvão, L., Ekevad, M. and Sitoe, R. (2011) Cutting forces for wood of lesser used species from Mozambique. In Proceedings of the 20th International Wood Machining Seminar (Skellefteå: Luleå University of Technology), pp. 444–451.
   Google Scholar
• Lundahl, C. G. (2009) Total quality management in sawmills. PhD Thesis. Luleå University of Technology, Skellefteå, Sweden.
   Google Scholar
• Lunstrum, S. J. (1985) Balanced saw performance. U.S. Department of Agriculture, Forest Service, Forest Products Utilization, Technical report no. 12, pp. 1–17.
   Google Scholar
• Moradpour, P., Doosthoseini, K., Scholz, F. and Tarmian, A. (2013) Cutting forces in bandsaw processing of oak and beech wood as affected by wood moisture content and cutting directions. European Journal of Wood and Wood Products, 71(6), 747–754.
   Web of Science ®Google Scholar
• Orlowski, K. (2007) Experimental studies on specific cutting resistance while cutting with narrow-kerf saws. Advances in Manufacturing Science and Technology, 31(1), 49–63.
   Google Scholar
• Orlowski, K., Sandak, J., Negri, M. and Dzurenda, L. (2009) Sawing frozen wood with narrow kerf saws: energy and quality effects. Forest Products Journal, 59(3), 79–83.
   Web of Science ®Google Scholar
• Orlowski, K. (2010) The fundamentals of narrow-kerf sawing: The mechanics and quality of cutting. Technical University in Zvolen.
   Google Scholar
• Shmulsky, R. and Shvets, V. (2006) The effect of subzero temperatures on FSP of cottonwood. Forest Products Journal, 56(2), 74.
   Web of Science ®Google Scholar
• Vazquez-Cooz, I. and Meyer, R. W. (2006) Cutting forces for tension and normal wood of maple. Forest Products Journal, 56(4), 26–34.
   Web of Science ®Google Scholar