References
- T. J. Grilo, R. M. F. Paulo, C. R. M. Silva and J. P. Davim: ‘Experimental delamination analyses of CFRPs using different drill geometries’, Composite: Part B, 2013, 45, 1344–1350.10.1016/j.compositesb.2012.07.057
- N. Z. Zarif Karimi, H. Heidary, G. Minak and M. Ahmadi: ‘Effect of the drilling process on the compression behavior of glass/epoxy laminates’, Compos. struct., 2013, 98, 59–68.10.1016/j.compstruct.2012.10.044
- D. Liu, Y. Tang and W. L. Cong: ‘A review of mechanical drilling for composite laminates’, Compos. Struct., 2012, 94, 1265–1279.10.1016/j.compstruct.2011.11.024
- A. M. Abrão, P. E. Faria, J. C. Campos Rubio, P. Reis and J. P. Davim: ‘Drilling of fibre reinforced plastics: A review’, J. Mater. Process. Technol., 2007, 186, 1–7.10.1016/j.jmatprotec.2006.11.146
- R. Piquet, B. Ferret, F. Lachaud and P. Swider: ‘Experimental analysis of drilling damage in thin carbon/epoxy plate using special drills’, Composites Part A, 2000, 31, (10), 1107–1115.10.1016/S1359-835X(00)00069-5
- J. P. Davim and P. Reis: ‘Study of delamination in drilling carbon fiber reinforced plastics (CFRP) using design experiments’, Compos. struct., 2003, 59, (4), 481–487.10.1016/S0263-8223(02)00257-X
- I. Singh and N. Bhatnagar: ‘Drilling of uni-directional glass fiber reinforced plastic (UD-GFRP) composite laminates’, Int. J. Adv. Manuf. Technol., 2006, 27, 870–876.10.1007/s00170-004-2280-7
- W. Chen: ‘Some experimental investigations in the drilling of carbon fibre reinforced plastics (CFRP) composite laminates’, Int. J. Mach. Tools Manuf., 1997, 37, (8), 1097–1108.
- E. Capello: ‘Workpiece damping and its effect on delamination damage in drilling thin composite laminates’, J. Mater. Process Technol., 2004, 148, (2), 186–195.10.1016/S0924-0136(03)00812-4
- U. A. Khashaba: ‘Delamination in drilling GFR-thermoset composites’, Compos. Struct., 2004, 63, 313–327.10.1016/S0263-8223(03)00180-6
- T. V. Rajamurugan, K. Shanmugam and K. Palanikumar: ‘Analysis of delamination in drilling glass fiber reinforced polyester composites’, Mater. Des., 2013, 45, 80–87.10.1016/j.matdes.2012.08.047
- T. A. Marques, M. L. Durão, G. A. Magalhães, F. J. Silva, R. S. Tavares and J. Manuel: ‘Delamination analysis of carbon fibre reinforced laminates: Evaluation of a special step drill’, Compos. Sci. Technol., 2013, 69, 2376–2382.
- D. Kumar and K. K. Singh: ‘An approach towards damage free machining of CFRP and GFRP composite material: a review’, Adv. Compos. Mater., 2015, 24, (1), 49–63.
- H. Hocheng and C. C. Tsao: ‘Effect of special drill bits on drilling-induced delamination of composite materials’, Int. J. Mach. Tools Manuf., 2006, 46, 1403–1416.
- C. X. Feng and W. X. Feng: ‘Development of empherical models for surface roughness prediction in finish turning’, Int. J. Adv. Manuf. Technol., 2013, 20, (5), 348–356.
- K. Palanikumar, L. Karunamoorthy and R. Karthikeyan: ‘Assessment of factors influencing surface roughness on the machining of glass fiber-reinforced polymer composites’, Mater. Des., 2006, 27, 862–871.10.1016/j.matdes.2005.03.011
- B. Latha and V. S. Senthilkumar: ‘Modeling and analysis of surface roughness parameters in drilling GFRP composite using fuzzy logic’, Mater. Manuf. processes, 2013, 25, 817–827.
- K. Palanikumar, B. Latha, V. S. Senthilkumar and J. P. Davim: ‘Analysis on drilling of glass fiber–reinforced polymer (GFRP) composites using grey relational analysis’, Mater. Manuf. Processes, 2012, 27, 297–305.10.1080/10426914.2011.577865
- H. Takeyama and N. Iijima: ‘Machinability of glassfiber reinforced plastics and application of ultrasonic machining’, CIRP Ann. – Manuf. Technol., 1988, 37, (1), 93–96.10.1016/S0007-8506(07)61593-5
- K. Palanikumar: ‘Experimental investigation and optimisation in drilling of GFRP composites’, Measurement, 2011, 44, 2138–2148.10.1016/j.measurement.2011.07.023
- M. A. J. Bosco, K. Palanikumar, B. D. Prasad and A. Velayudham: ‘Influence of machining parameters on delamination in drilling of GFRP-armour steel sandwich composites’, Procedia Eng., 2013, 51, 758–763.10.1016/j.proeng.2013.01.108
- I. S. Shyha, D. K. Aspinwall, S. L. Soo and S. Bradley: ‘Drilling geometry and operating effects when cutting small diameters holes in CFRP’, Int. J. Mach. Tools Manuf., 2009, 49, 1008–1014.
- N. S. Mohan, S. M. Kulkarni and A. Ramachandra: ‘Delamination analysis in drilling process of glass fiber reinforced plastic (GFRP) composite materials’, J. Mater. Process. Technol., 2007, 186, 265–271.10.1016/j.jmatprotec.2006.12.043
- S. Ponnuvel and T. V. Moorthy: ‘Investigation on the influence of multi walled carbon nanotubes on delamination in drilling epoxy/glass fabric polymeric nanocomposite’, Procedia Eng., 2013, 51, 735–744.10.1016/j.proeng.2013.01.105