References
- Cotell C, Sprague JA. ‘ASM Handbook’, ‘Surface engineering’. Vol. 5. Materials Park (OH): ASM International; 1994.
- Ayers JD, Schaefer RJ. In: Ready JF, editor. Proceeding Conference ‘Laser applications in material processes’; Bellingham. SPIE; 1979. p. 57–64, 198.
- Fasasi AY, Pons M, Tassin C, et al. Laser surface melting of mild steel with submicronic titanium carbide powders. J Mater Sci. 1994;29:5121–5126.10.1007/BF01151106
- Selamat MS, Watson LM, Baker TN. Study of the surface layer formed by the laser processing of Ti–6Al–4V alloy in a dilute nitrogen environment. J Mater Proc Technol. 2003;142:725–737.10.1016/S0924-0136(03)00814-8
- Baker TN. Chapter 12. In: Dong H, editor. Surface engineering of light alloys; aluminium, magnesium and titanium alloys. Oxford: Woodhead Publishing; 2010, p.398–443.10.1533/9781845699451.2.398
- Weng F, Chen CZ, Yu HJ. Research status of laser cladding on titanium and its alloys: a review. Mater Des. 2014;58:412–425.10.1016/j.matdes.2014.01.077
- Atamert S, Bhadeshia HKDH. Comparison of the microstructures and abrasive wear properties of stellite hardfacing alloys deposited by arc-welding and laser cladding. Metall Trans A. 1989;20:1037–1054.
- Mridha S, Ho SY, Kum ST. Surface Layer Addition of Hard Particles using TIG Arc Melting. In: Khor KA, Srivatsan TS, Moore JJ, editors. Conf.proc, ‘Processing and Fabrication of Advanced MaterialsVI’; Singapore; 1998. p. 1331–1338.
- Mridha S, Dyutti S. Formation of TiN dispersed composite layer on steel surfaces by titanium powder preplacement and TIG surface melting processes. Adv Mater Res. 2011;264–265:1415–1420.
- Wang XH, Song SL, Zou ZD. Fabricating TiC particles reinforced Fe-based composite coatings produced by GTAW multilayers melting process. Mater Sci Eng A. 2006;441:60–67.10.1016/j.msea.2006.06.015
- Lyttle KA. Shielding gases. ASM Handbook Weld Brazing Soldering. 1993;6:64–69.
- Walker A, Folkes J, Steen WM, et al. Laser surface alloying of titanium substrate with carbon and nitrogen. Surf Eng. 1985;1:23–29.10.1179/sur.1985.1.1.23
- Xin H, Watson LM, Baker TN. Surface analytical studies of a laser nitrided Ti–6Al–4V alloy: a comparison of spinning and stationary laser beam modes. Acta Mater. 1998;46:1949–1961.10.1016/S1359-6454(97)00438-2
- Hoeche D, Schaaf P. Laser nitriding: investigations on the model system TiN. A review. Heat Mass Trans. 2011;47:519–540.10.1007/s00231-010-0742-z
- Mridha S, Baker TN. Metal matrix composite layer formation with 3 mu m SiCp powder on IMI318 titanium alloy surfaces through laser treatmentJ. J Mater Process Technol. 1997;63:432–437.10.1016/S0924-0136(96)02660-X
- Chen YB, Liu DJ, Li FQ, et al. WCp/Ti–6Al–4 V graded metal matrix composites layer produced by laser melt injection. Surf Coat Technol. 2008;202:4780–4787.10.1016/j.surfcoat.2008.04.057
- Kooi BJ, Pei YT, De Hosson JTM. The evolution of microstructure in a laser clad TiB-Ti composite coating.Acta Mater. 2003;51:831–845.
- Wang XH, Song SL, Qu SY, et al. Characterization of in situ synthesized TiC particle reinforced Fe-based composite coatings produced by multi-pass overlapping GTAW melting process. Surf Coat Technol. 2007;201:5899–5905.10.1016/j.surfcoat.2006.10.042
- Mridha S, Idriss AN Md, Baker TN. Incorporation of TiC particles on AISI 4340 low alloy steel surfaces via tungsten inert gas arc melting. Adv Mater Res. 2012;445:655–660.
- Ulutan M, Yildirim MM, Buytoz S, Celik ON. Microstructure and wear behavior of TIG surface-alloyed AISI 4140 steel. Tribo Trans. 2011;54:67–79.
- Hu C, Baker TNJ. Overlapping laser tracks to produce a continuous nitrided layer in Ti–6Al–4 V alloy. J Mater Sci. 1997;32:2821–2826.10.1023/A:1018664231410
- Patel P, Mridha S, Baker TN. Influence of shielding gases on preheat produced in surface coatings incorporating SiC particulates into microalloy steel using TIG technique. Mater Sci Technol. 2014;30:1506–1514.10.1179/1743284713Y.0000000481
- Muñoz-Escalona P, Mridha S, Baker TN. Effect of silicon carbide particle size on microstructure and properties of a coating layer on steel produced by TIG technique. Adv Mater Proc Technol. 2015;1:435–443.
- Easterling KE. Introduction to the physical metallurgy of welding. London: Butterworth-Heinemann; 1992.
- DuPont JN, Marder AR. Thermal efficiency of arc-welding processes. Welding J. 1995;74:406s–416s.
- Thawari G, Sundarararjan G, Joshi SV. Laser surface alloying of medium carbon steel with SiC(P). Thin Solid Films. 2003;423:41–53.10.1016/S0040-6090(02)00974-4
- Wriedt HA. ASM handbook’, ‘Alloy phase diagrams’, 2–199, 3. Materials Park (OH): ASM International; 1992.