REFERENCES
- Armarego , E.J. A. and Deshpande , N. P. 1989 . Computerized end-milling force predictions with cutting models allowing for eccentricity and cutter deflections . CIRP Ann. , 38 ( 1 ) : 45 – 49 .
- Armarego , E.J. A. and Deshpande , N. P. Aug. 1993 . Force prediction models and CAD/CAM software for helical tooth milling processes I. Basic approach and cutting analyses . Int. J. Prod. Res. , : 1991 – 2009 .
- Elbestawi , M. A. , Ismail , F. , Du , R. and Ullagaddi , B. C. 1994 . Modeling machining dynamics including damping in the tool-workpiece interface . Trans. ASME, Ser. B , 116 : 435 – 439 .
- Gu , F. , Kapoor , S. G. , DeVor , R. E. and Bandhopadhyay , P. 1991 . An approach to on-line cutter runout estimation in face milling . Trans. NAMRI/SME , : 240 – 247 .
- Kline , W. A. and DeVor , R. E. 1983 . The effect of runout on cutting geometry and forces in end milling . Int. J. Mach. Tool Des. Res. , 23 : 123 – 140 .
- Liang , S. Y. and Wang , J. J. 1994 . Milling force convolution modeling for identification of cutter axis offset . Int. J. Mach. Tools Manuf. , : 1171 – 1190 .
- Liang , S. Y. , Wang , J. J. and Herman , P. A. 1993 . Surface finish enhancement in end milling via inverse runout trajectory following . Trans. NAMRI/SME , : 103 – 109 .
- Liang , S. Y. and Zheng , L. 1997 . Identification of cutter axis tilt in end milling . Trans. ASME, J. Manuf. Sci. Eng. , : 178 – 185 .
- Melkote , S. N. and Thangaraj , A. R. 1994 . An enhanced surface texture model for end milling including the effects of radial rake and relief angles . Trans. ASME, Ser. B , 116 ( 2 ) : 166 – 174 .
- Montgomery , D. and Altintas , Y. 1991 . Mechanism of cutting force and surface generation in dynamic milling . Trans. ASME, Ser. B , 113 : 160 – 168 .
- Ranganath , S. , Liu , D. and Sutherland , J. W. 1998 . A comprehensive model for the flank face interference mechanism in peripheral milling . Trans. NAMRI/SME , : 249 – 254 .
- Ranganath , S. , Narayanan , K. and Sutherland , J. W. Nov. 1999 . A dynamic model of the cutting force system in peripheral milling characterizing the effects of flank face interference . ASME J. Manuf. Sci. Eng. , : 593 – 599 .
- Stephenson , D. A. and Bandyopadhyay , P. 1995 . “ Process independent force characterization for machining simulation ” . In ASME MED 15 – 36 . New York : ASME . Vol. 1/DE Vol. 85
- Sutherland , J. W. 1988 . A dynamic model of the cutting force system in the end milling process . Sens. Controls Adv. Manuf. PED , 33 : 53 – 62 .
- Tlusty , J. and MacNeil , P. 1975 . Dynamics of cutting forces in end milling . Ann. CIRP , 24 : 21 – 25 .
- Yellowley , I. 1988 . A note on the significance of the quasi mean resultant forces and the modeling of instantaneous torque and forces in peripheral milling operations . Trans. ASME, Ser. B , 110 : 300 – 303 .