REFERENCES
- Komanduri , R. and Brown , R. H. 1981 . On the mechanics of the chip formation in machining . J. Eng. Ind. , 103 : 33 – 51 .
- Komanduri , R. , Schroeder , T. , Hazra , J. , Von Turovich , B. F. and Flom , D. G. 1982 . On the catastrophic shear instability in high speed machining of an AISI 4340 steel . J. Eng. Ind. , 104 : 121 – 131 .
- Semiatin , S. L. and Rao , S. B. 1983 . Shear localization during metal cutting . J. Mater. Sci. Eng. , 61 : 185 – 192 .
- König , W. , Berktold , A. and Koch , F. K. 1993 . Turning versus grinding—a comparison of surface integrity aspects and attainable accuracies . Ann. ICRP , 42 : 39 – 43 .
- Shaw , M. C. and Vyas , A. 1993 . Chip formation in the machining of hardened steel . Ann. ICRP , 42 ( 1 ) : 29 – 33 .
- Hou , Z. B. and Komanduri , R. 1995 . On a thermomechanical model of shear instability in machining . Ann. ICRP , 44 ( 1 ) : 69 – 73 .
- Davies , M. A. , Chou , Y. and Evans , C. J. 1996 . On chip morphology, tool wear and cutting mechanics in finish hard turning . Ann. ICRP , 45 : 77 – 82 .
- Elbestawi , M. A. , Srivastava , A. K. and El-wardany , T. 1996 . A model for chip formation during machining of hardened steel . Ann. ICRP , 45 ( 1 ) : 71 – 76 .
- Kishawy , H. A. and Elbestawi , M. A. 1997 . On the Mechanics and Properties of Chip Formation during Machining of Hardened Steel, Thirty Second International Matador Conference, Manchester 253 – 258 .
- Hou , Z. B. and Komanduri , R. 1997 . Modelling the thermomechanical shear instability in machining . Int. J. Mech. Sci. , 39 ( 11 ) : 1273 – 1314 .
- Kishawy , H. A. 1998 . “ Chip Formation and Surface Integrity in High Speed Machining of Hardened Steel ” . In Ph.D. thesis Hamilton, Ontario, Canada : McMaster University .
- Kishawy , H. A. and Elbestawi , M. A. 1997 . Effect of process parameters on chip morphology when machining hardened steel . ASME Int. Eng. Congr. Exp. Manuf. Sci. Technol. , 2 : 13 – 20 .
- Liu , C. R. and Barash , M. M. 1982 . Variables governing patterns of mechanical residual stress in a machined surface . J. Eng. Ind. , 104 ( 3 ) : 257 – 264 .
- Matsumoto , Y. , Barash , M. M. and Liu , C. R. 1986 . Effect of hardness on the surface integrity of AISI 4340 steel . J. Eng. Ind. , 108 ( 3 ) : 169 – 175 .
- Tönshoff , H. K. , Wobker , H. G. and Brandt , D. 1995 . Hard turning—influences on the workpiece properties . Trans. NAMRI/SME , XXIII : 215 – 220 .
- Kishawy , H. A. and Elbestawi , M. A. 1998 . Effect of edge preparation and cutting speed on surface integrity of die materials in hard machining . ASME Int. Eng. Congr. Exp. Manuf. Sci. Technol. , 2 : 269 – 276 .
- Kishawy , H. A. and Elbestawi , M. A. 1999 . Effect of process parameters on material side flow during hard turning . Int. J. Mach. Tools Manuf. , 39 : 1017 – 1030 .
- Abrao , A. M. , Aspinwall , D. K. and Wise , M. L.H. 1995 . Tool wear, cutting forces and temperature evaluation when turning hardens bearing steel using PCBN and ceramic tool material . Int. MATADO Conf. , : 209 – 216 .
- Boothroyd , G. 1963 . Temperatures in orthogonal metal cutting . Proc. Inst. Mech. Eng., IMechE Conf. , 177 ( 29 ) : 789 – 810 .
- Barrow , G. 1973 . A review of experimental and theoretical techniques for assessing cutting temperature . Ann. ICRP , 22 ( 2 ) : 203 – 211 .
- Kato , S. , Yamaguchi , K. , Watanabe , Y. and Hiraiwa , Y. 1976 . Measurement of temperature distribution within tool using powders of constant melting point . J. Eng. Ind. , : 607 – 613 .
- Narutaki , N. , Yamane , Y. and Okushima , K. 1979 . Tool wear and cutting temperature on CBN tools in machining of hardened steels . Ann. ICRP , 28 ( 1 ) : 23 – 28 .
- Stephenson , D. A. 1991 . Assessment of steady-state metal cutting temperature models based on simultaneous infrared and thermocouple data . J. Eng. Ind. , 113 : 121 – 128 .
- Mohammed , E. 1994 . “ Cutting Performance and Tool Failure Characteristics During Machining of Difficult to Cut Materials Using Ceramic Tools ” . In M. Eng. Thesis Hamilton, Ontario, Canada : McMaster University .
- Udea , T. , Al Huda , M. , Tamada , K. and Nakayama , K. 1999 . Temperature measurements of CBN tool in turning of high hardness steel . Ann. ICRP , 48 ( 1 ) : 63 – 66 .
- Wang , Y. and Liu , C. R. 1999 . The effect of tool flank wear on the heat transfer, thermal damage, and cutting mechanics in finish hard turning . Ann. ICRP , 48 : 53 – 58 .
- El-Wardany , T. I. , Mohammed , E. and Elbestawi , M. A. 1996 . Cutting temperature of ceramic tools in high speed machining of difficult-to-cut materials . Int. J. Mach. Tools Manuf. , 36 ( 5 ) : 611 – 634 .
- Chou , Y. S. and Barash , M. M. Review on Hard Turning and CBN Cutting Tools . 1st International Machining and Grinding Conference . Sep. 12–14 . pp. 951 – 962 . Michigan, USA : Society of Manufacturing Engineers .
- Hodgson , T. and Trendler , P. H. Cubic Boron Nitride Machining; with Particular to Cutting Tool Geometry and Cutting Forces when Machining Tool Steel . Proceeding of International Conference on Manufacturing Engineering . Melbourne, Australia. pp. 63 – 70 .
- Trent , E. M. 1991 . Metal Cutting , 3rd Ed. Butterworth-Heinemann .