References
- Tandon R et al.: ‘Magnesium powder technology for ultra lightweight applications,’ Proc. Int. Conf. on Powder Metallurgy and Particulate Materials, Vol. II, 07–157–07–163; 2011, Princeton, NJ, MPIF.
- Mathaudhu S: ‘Magnesium alloys in U.S. military applications: past, current and future solutions’, in ‘Magnesium technology 2010’, 27–32; 2010, Warrendale, PA, TMS.
- Gywnne B: ‘Magnesium alloys in aerospace applications–flammability testing and results’, in ‘Magnesium technology 2010’, 13–16; 2010, Warrendale, PA, TMS.
- Cho K et al.: ‘Magnesium technology and manufacturing for ultra lightweight armored ground vehicles’, Proc. 2008 Army Science Conf., Orlando, FL, USA, 2008.
- Rick Delrome et al.: ‘Ultra light metallic armor (ULMA)-magnesium hard alloys as the defense against modern warfare threats’, Proc. Conf. Magnesium Technology 2010, TMS.
- Jones T and Kondoh K: ‘Ballistic analysis of new military grade magnesium alloys for armor applications’, in ‘Magnesium technology 2010’, 425–430; 2010, Warrendale, PA, TMS.
- Tandon R: ‘Additive manufacturing using magnesium alloy powders’, Proc. PM 2014 World Cong., Orlando, FL, USA, MPIF.
- Andersson P, Caceres CH and Koike J: ‘Hall–Petch parameters for tension and compression in cast Mg,’ Mater. Sci. Forum, 2003, 419–422, 123–128.
- Kawamura Y and Inoue A: ‘Rapidly solidified powder metallurgy Mg97Zn1Y2 alloys with tensile yield strength of 610 MPa and elongation of 5%’, in ‘Magnesium technology 2002’; 2002, Warrendale, PA, TMS.
- Elsayed A, Umeda J and Kondoh K: ‘The production of powder metallurgy hot extruded Mg–Al–Mn–Ca alloy with high strength and limited anisotropy’, in ‘Magnesium technology 2011’, 475–480; 2011, Warrendale, PA, TMS.
- Bettles CJ, Moss MH and Lapovok R: ‘A Mg–Al–Nd alloy produced via a powder metallurgical route’, Mater. Sci. Eng. A, 2009, 515, 26–32.
- Segal VM: ‘Engineering and commercialization of equal channel angular extrusion (ECAE)’, Mater. Sci. Eng. A, 2004, 386, 269–276.
- Paydar MH et al.: ‘Consolidation of Al particles through forward extrusion-equal channel angular pressing (FE-ECAP), Mater. Lett., 2008, 62, 3266–3268.
- Ng CC et al.: ‘Layer manufacturing of magnesium and its alloy structures for future applications,’ Virtual Phys. Prototyp., 2010, 5, (1) 13–19.
- Wolff M et al.: ‘Properties of sintered Mg alloys for biomedical applications’, Mater. Sci. Forum, 2011, 690, 491–494.
- Wolff M et al.: ‘Advances in the metal injection molding of Mg–Ca alloys for biomedical applications,’ PIM Int., 2012, 6, (4), 59–63.
- Kainer K.-U, Ebel T, Ferri OM, Limberg W, Pyczak F, Schimansky F.-P and Wolff M: ‘From titanium to magnesium: processing by advanced metal injection moulding’, Powder Metall., 2012, 55, 315–321.
- Champagne VK and Helfritch DJ: ‘Mainstreaming cold spray – push for applications’, Surf. Eng., 2014, 30, 396–403.
- Moridi A, Hassani-Gangaraj SM, Guagliano M and Dao M: ‘Cold spray coating: review of material systems and future perspectives’, Surf. Eng., 2014, 30, 369–395.
- Mishra RS and Ma ZY: ‘Friction stir welding and processing’, Mater. Sci. Eng. R, 2005, 50, 1–78.
- Lowe TC and Valiev RC: ‘Frontiers for bulk nanostructured metals in biomedical applications’, in ‘Advanced biomaterials and biodevices’, (ed. Tiwari A and Nordin A N), 3–52; 2014, New York, Scrivener.
- Kirkland NT: ‘Magnesium biomaterials: past, present and future’, Corros. Eng. Sci. Technol., 2012, 47, 322–328.
- Tandon R et al.: ‘Influence of powder characteristics on the consolidation behavior of magnesium alloys for structural and energetic applications’, Proc. Int. Conf. on Powder Metallurgy and Particulate Materials, Vol. II, 07–157–07–163; 2012, Princeton, NJ, MPIF.
- Magnesium Elektron 21 Datasheet 455, www.magnesium-elektron.com.
- Magnesium Elektron WE43B Datasheet 467A & Datasheet 478, www.magnesium-elektron.com.