Study of interface and base metal microstructures in explosive clad joint of Ti–5Ta–1·8Nb and 304L stainless steel

References

• Raj B, Mudali UK: ‘Materials development and corrosion problems in nuclear fuel reprocessing plants’, Prog. Nucl. Energy, 2006, 48, 283–313.
   Web of Science ®Google Scholar
• Mudali UK, Rao BMA, Shanmugam K, Natarajan R, Raj B: ‘Corrosion and microstructural aspects of dissimilar joints of titanium and type 304L stainless steel’, J. Nucl. Mater., 2003, 321, 40–48.
   Web of Science ®Google Scholar
• Wu MF, Yu C, Yu ZS, Li RF: ‘A study of Ti/Fe contact reaction structures’, Mater. Sci. Technol., 2004, 20, 658–660.
   Web of Science ®Google Scholar
• Kundu S, Chatterjee S, Olson D, Mishra B: ‘Effects of intermetallic phases on the bond strength of diffusion bonded joints between titanium and 304 stainless steel using nickel interlayer’, Metall. Mater. Trans. A, 2007, 38A, 2053–2060.
   Web of Science ®Google Scholar
• Merriman C: ‘The fundamentals of explosion welding’, Weld. J., 2006, 85, 27–29.
   Web of Science ®Google Scholar
• Pocalyko A: ‘Explosion clad plate for corrosion service’, Mater. Prot., 1965, 4, (6), 10–15.
   Google Scholar
• Kocar R, Acarer M: ‘Microstructure–property relationship in explosively welded duplex stainless steel–steel’, Mater. Sci. Eng. A, 2003, A363, 290–296.
   Google Scholar
• Arthur G: ‘Applications of explosive welding to heat exchangers’, Mater. Des., 1985, 6, (1), 37–41.
   Google Scholar
• Nishida M, Chiba A, Imamura K, Minato H, Shudo J: ‘Microstructural modifications in an explosive welded Ti/Ti clad material: bonding interface’, Metall. Mater. Trans. A, 1993, 24A, 735–742.
   Google Scholar
• Pocalyko A: ‘Fabrication of explosion‐welded titanium‐clad composites’, Weld. J., 1987, 25, 24–30.
   Google Scholar
• Nishida M, Chiba A, Ando S, Imamura K, Minato H: ‘Microstructural modifications in an explosively welded Ti/Ti clad material: II. Deformation structures around bonding interface’, Metall. Mater. Trans. A, 1993, 24A, 743–750.
   Google Scholar
• Kosec B, Kosec L, Petrovic S, Gontarev V, Kosec G, Gojic M, Skraba P: ‘Analysis of low carbon steel/titanium interface after explosive welding’, Metallurgija, 2003, 42, (3), 147–151.
   Web of Science ®Google Scholar
• Akbari‐Mousavi SAA, Barrett LM, Al‐Hassani STS: ‘Explosive welding of metal plates’, J. Mater. Proc. Technol., 2008, 202, 224–239.
   Web of Science ®Google Scholar
• Akbari‐Mousavi SAA, Sartangi PF: ‘Experimental investigation of explosive welding of cp‐titanium/AISI 304 stainless steel’, Mater. Des., 2009, 30, 459–468.
   Web of Science ®Google Scholar
• Kartikeyan T, Dasgupta A, Saroja S, Vijayalakshmi M: ‘Solidification structures in Ti–5Ta–1·8Nb weld’, Sci. Technol. Weld. Join., 2009, 14, 597–605.
   Google Scholar
• Mythili R, Saroja S, Vijayalakshmi M, Raghunathan VS: ‘Selection of optimum microstructure for improved corrosion resistance in a Ti–5%Ta–1·8%Nb alloy’, J. Nucl. Mater., 2005, 345, 167–183.
   Web of Science ®Google Scholar
• Mythili R, Paul VT, Saroja S, Vijayalakshmi M, Raghunathan VS: ‘Study of transformation behavior in Ti–4·4Ta–1·9Nb alloy’, Mater. Sci. Eng. A, 2005, A390, 299–312.
   Google Scholar
• Wang L, Lu W, Qin J, Zhang F, Zhang D: ‘Influence of cold deformation on martensitic transformation and mechanical properties of Ti–Nb–Ta–Zr alloy’, J. Alloys Compd, 2009, 469, 512–518.
   Web of Science ®Google Scholar
• Tamhankar RV, Ramesam J: ‘Metallography of explosive welds’, Mater. Sci. Eng., 1974, 13, 245–254.
   Google Scholar
• Van Heerden D, Josell D, Shechtman D: ‘Formation of fcc titanium in titanium–aluminium multilayers’, Acta Mater., 1996, 44, (1), 297–306.
   Web of Science ®Google Scholar
• Tepper T, Shechtman D, Van Heerden D, Josell D: ‘fcc titanium in titanium/silver multilayers’, Mater. Lett., 1997, 33, 181–184.
   Web of Science ®Google Scholar
• Zhang DL, Ying DY: ‘Formation of fcc titanium during heating high energy, ball milled Al–Ti powders’, Mater. Lett., 2001, 50, 149–153.
   Web of Science ®Google Scholar
• Phasha AJ, Kasonde H, Ngoepe PE: ‘Effect of pressure on the metastable phase formation of equilibrium immiscible Ti–Mg system studied by ab‐initio technique and mechanical milling’, 2008, http://researchspace.csir.co.za/dspace/bitstream/…/1/Phasha_P_2008.pdf
   Google Scholar
• Asano K, Enoki H, Akiba E: ‘Synthesis of HCP, FCC and BCC structure alloys in the Mg–Ti binary system by means of ball milling’, J. Alloys Compd, 2009, 480, 558–563.
   Web of Science ®Google Scholar
• Rhodes CG, Williams JC: ‘Observations of an interface phase in the α/β boundaries in titanium alloys’, Metall. Mater. Trans. A, 1975, 6A, 1670–1671.
   Web of Science ®Google Scholar
• Tavares SSM, Pardal JM, da Silva MJG, Abreu HFG, da Silva MR: ‘Deformation induced martensitic transformation in a 201 modified austenitic stainless steel’, Mater. Charact., 2009, 60, 907–911.
   Web of Science ®Google Scholar
• da Rocha MR, de Oliveira CAS: ‘Evaluation of the martensitic transformations in stainless steel’, Mater. Sci. Eng. A, 2009, A517, 281–285.
   Google Scholar
• Das A, Tarafder S: ‘Experimental investigation on martensitic transformation and fracture morphologies of austenitic stainless steel’, Int. J. Plast, 2009, 25, (11) 2222–2247.
   Web of Science ®Google Scholar
• Jaramillo D, Szecket A, Inal OT: ‘On the transition from a waveless to a wavy interface in explosive welding’, Mater. Sci. Eng., 1987, 91, 217–222.
   Google Scholar
• Akbari‐Mousavi SAA, Al‐Hassani STS, Atkins AG: ‘Bond strength of explosive welded specimens’, Mater. Des., 2008, 29, 1334–1352.
   Web of Science ®Google Scholar
• Kahraman N, Gulenc B, Findik F: ‘Joining of titanium/stainless steel by explosive welding and effect on interface’, J. Mater. Proc. Technol., 2005, 169, 127–133.
   Web of Science ®Google Scholar
• Xia CQ, Jin ZP: ‘On the evolution of microstructure and diffusion paths in the titanium–steel explosion weld interface during heat treatment’, J. Less Common Met., 1990, 162, 315–322.
   Google Scholar
• Manikandan P, Hokamoto K, Fujita M, Raghukandan K, Tomoshige R: ‘Control of energetic conditions by employing interlayer of different thickness for explosive welding of titanium/304 stainless steel’, J. Mater. Proc. Technol., 2008, 195, 232–240.
   Web of Science ®Google Scholar