References
- Savage WF: ‘Flash welding – process variables and weld properties’, Weld. J., 1962, 41, 109-s–119-s.
- Resistance Welder Manufacturers’ Association: ‘Resistance welding manual’, revised edn, 5–13; 2003, Philadelphia, PA, RMWA.
- Sullivan JF, Savage WF: ‘Effect of phase control during flashing on flash weld defects’, Weld. J., 1971, 70, 213-s–221-s.
- Ichiayama Y, Saito T: ‘Factors affecting flash weldability in high strength steel – a study on toughness improvement of flash welded joints in high strength steel’, Weld. Int., 2004, 18, 436–443.
- Riecansky V, Lucas W: ‘Formation and significance of weld line defects in flash welded mild steel tube and bar’, Weld. Int., 1974, 4, 1–27.
- Nippes EF, Savage WF, Grotke G, Robelotto M: ‘Studies of upset variables in the flash welding of steel’, Weld. J., 1957, 36, 192-s–211-s.
- Taka T, Kunishige K, Yamauchi N, Nagao N: ‘Hot-rolled steel sheet with excellent flash weldability for automotive wheel rim use’, ISIJ Int., 1989, 29, 503–510.
- Räsänen A.-N, Kah P, Salo J, Martikainen J: ‘Quality assurance of flash welding in endless wire rod rolling production’, Proc. 2nd South-East Asia Int. Weld. Cong., Bangkok, Thailand, February 2010, Welding Institute of Thailand, Paper 34.
- Mansouri H, Monshi A: ‘Microstructure and residual stress variations in weld zone of flash-butt welded railroads’, Sci. Technol. Weld. Join., 2004, 9, 237–245.
- Kim DC, So WJ, Kang MJ: ‘Effect of flash butt welding parameters on weld quality of mooring chain’, Arch. Mater. Sci. Eng., 2009, 38, 112–117.
- Saito T, Ichiyama Y: ‘Weld defects and evaluation of weld quality: welding phenomena and process control on flash welding of steel sheets (1st report)’, Weld. Int., 1996, 10, 117–123.
- Lonsdale CP: ‘An investigation of weld line defects in electric flash butt welds’, Proc. 36th Conf. on ‘Mechanical working and steel processing’, 1101–1109; 1997, Warrendale, PA, ISS.
- Shinozaki M, Kato T, Irie T, Hashimoto H: ‘Effects of chemical composition and structure of hot rolled high strength steel sheets on the formability of flash welded joints’, Kawasaki steel technical report no. 6, Kawasaki Steel Corporation, Tokyo, Japan, 1982.
- Kuchuk-Yatsenko SI, Radko VP, Kazymov BI, Zyakhor IV, V Nikolnikov A: ‘Pecularities of detection of defects in FBW joints on pipes by ultrasonic inspection’, Weld. J., 2007, 1, 31–35.
- Saito T, Ichiyama Y: ‘Correlation between welding phenomena and weld defects before and after start of upsetting: welding phenomena and process control in flash welding of steel sheet (2nd report)’, Weld. Int., 1996, 10, 173–180.
- Ichiyama Y, Kodama S: ‘Flash-butt welding of high strength steel’, Nippon Steel technical report no. 95, 81–87, Nippon Steel Corporation, Tokyo, Japan, 2007.
- Krishnaraj N, Prasad Rao K, Ramachandran EG: ‘The quality of flash welded joints in mild steel: a study on the effects of welding parameters’, Weld. J., 1993, 72, 239-s–245-s.