References
- J. Zhang, L. F. He and Y. C. Zhou: ‘Highly conductive and strengthened copper matrix composite reinforced by Zr2Al3C4 particulates’, Scr. Mater., 2009, 60, 976–979.
- Z. W. Xue, L. D. Wang, Z. Liu and W. D. Fei: ‘Effect of interfacial state on thermal expansion behaviors of β-LiAlSiO4 particulate-reinforced Cu composites’, Scr. Mater., 2010, 62, 867–870.
- Th. Schubert, B. Trindade, T. Weiβgärber and B. Kieback: ‘Interfacial design of Cu-based composites prepared by powder metallurgy for heat sink applications’, Mater. Sci. Eng., 2008, 475, 39–44.
- S. C. Vettivel, N. Selvakumar, R. Narayanasamy and N. Leema: ‘Numerical modelling, prediction of Cu–W nano powder composite in dry sliding wear condition using response surface methodology’, Mater. Des., 2013, 50, 977–996.
- N. Selvakumar and S. C. Vettivel: ‘Thermal, electrical and wear behavior of sintered Cu–W nanocomposite’, Mater. Des., 2013, 46, 16–25.
- P. Maji, R. K. Dube and B. Basu: ‘Enhancement of wear resistance of copper with tungsten addition (≤20 wt %) by powder metallurgy route’, J. Tribol., 2009, 131, 041602–041602–9.
- J. P. Tu, W. X. Qi, Y. Z. Yang, F. Liu, J. T. Zhang, G. Y. Gan, N. Y. Wang, X. B. Zhang and M. S. Liu: ‘Effect of aging treatment on the electrical sliding wear behavior of Cu–Cr–Zr alloy’, Wear, 2002, 249, 1021–1027.
- S. G. Jia, P. Liu, F. Z. Ren, B. H. Tian, M. S. Zheng and G. S. Zhou: ‘Wear behavior of Cu–Ag–Cr alloy wire under electrical sliding’, Mater. Sci. Eng., 2005, 398, 262–267.
- W. Ma, J. Lu and B. Wang: ‘Sliding friction and wear of Cu-graphite against 2024, AZ91D and Ti6Al4V at different speeds’, Wear, 2009, 266, 1072–1081.
- J. Kovacik, S. Emmer, J. Bielek and L. Kelesi: ‘Effect of composition on friction coefficient of Cu–graphite composites’, Wear, 2008, 265, 417–421.
- W. Xu, R. Hu, J. Li, Y. Zhang and H. Fu: ‘Tribological behavior of CNTs–Cu and graphite–Cu composites with electric current’, Trans. Nonferr. Met. Soc. China, 2012, 22, 78–84.
- R. Liu, K. Song, S. Jia, X. Xu, J. Gao and X. Guo: ‘Morphology and frictional characteristics under electrical currents of Al2O3/Cu composites prepared by internal oxidation’, Chin. J. Aeronaut., 2008, 21, 281–288.
- S. Azem, M. Nechiche and K. Taibi: ‘Development of copper matrix composite reinforced with FeAl particles produced by combustion synthesis’, Powder Technol., 2011, 208, 515–520.
- R. G. Zheng, Z. J. Zhan and W. K. Wang: ‘Wear behavior of Cu–La2O3 composite with or without electrical current’, Wear, 2010, 268, 72–76.
- M. D. Bryant, A. Tewari and J. Lin: ‘Wear rate reductions in carbon brushes, conducting current, and sliding against wavy copper surfaces’, IEEE Trans. Compon. Packag. Manuf. Technol. A, 1995, 18, 375–381.
- S. Xia, J. He, L. Chen, Z. Xiao and J. Li: ‘Studies on interference fit between armature and rails in railguns’, IEEE Trans. Plasma Sci., 2011, 39, 186–191.
- C. Persad and Z. Castro: ‘Railgun tribology: characterization and control of multishot wear debris’, IEEE Trans. Magn., 2007, 43, 173–177.
- B. L. Bramfitt: ‘The effect of carbide and nitride additions on the heterogeneous nucleation behavior of liquid iron’, Metall. Mater. Trans., 1970, 1, 1987–1995.