Failure mode of HSLA/DQSK dissimilar steel resistance spot welds

References

• Sun X, Stephens EV, Khaleel MA: ‘Effects of fusion zone size and failure mode on peak load and energy absorption of advanced high strength steel spot welds under lap shear loading conditions’, Eng. Fail. Anal., 2008, 15, 356–367.
   Web of Science ®Google Scholar
• Pouranvari M, Abedi A, Marashi P, Goodarzi M: ‘Effect of expulsion on peak load and energy absorption of low carbon resistance spot welds’, Sci. Technol. Weld. Join., 2008, 13, 39–43.
   Web of Science ®Google Scholar
• Sun X, Stephens EV, Davies RW, Khaleel MA, Spinella DJ: ‘Effects of failure modes on strength of aluminum resistance spot welds’, Weld. J., 2004, 83, 188s–195s.
   Web of Science ®Google Scholar
• Zhang H, Senkara J: ‘Resistance welding: fundamentals and applications’; 2005, Boca Raton, FL, Taylor & Francis CRC Press.
   Google Scholar
• Zhang H, Zhou M, Hu SJ: ‘Impact strength measurement of spot welds’, Proc. Inst. Mech. Eng. B: J. Eng. Manuf. , 2001, 215, 403–414.
   Web of Science ®Google Scholar
• Nieto J, Guerrero-Mata MP, Colas R, Mani A: ‘Experimental investigation on resistance spot welding of galvannealed HSLA steel’, Sci. Technol. Weld. Join., 2006, 11, 717–722.
   Web of Science ®Google Scholar
• Pouranvari M, Marashi SPH: ‘Key factors influencing mechanical performance of dual phase steel resistance spot welds’, Sci. Technol. Weld. Join., 2010, 15, 149–155.
   Web of Science ®Google Scholar
• Zuniga SM: ‘Predicting overload pull-out failures in resistance spot welded’, PhD thesis, Stanford University, Stanford, CA, USA, 1994.
   Google Scholar
• Marya M, Gayden XQ: ‘Development of requirements for resistance spot welding dual-phase (DP600) steels. Part 2. Statistical analyses and process maps’, Weld. J., 2005, 84, 197s–204s.
   Web of Science ®Google Scholar
• Hernandez VHBaltazar, Kuntz ML, Khan MI, Zhou Y: ‘Influence of weld size and microstructure of dissimilar AHSS resistance spot welds’, Sci. Technol. Weld. Join., 2008, 13, 769–776.
   Web of Science ®Google Scholar
• Alenius M, Pohjanne P, Somervuori M, Hanninen H: ‘Exploring the mechanical properties of spot welded dissimilar joints for stainless and galvanized steels’, Weld. J., 2006, 85, 305s–313s.
   Web of Science ®Google Scholar
• Marashi P, Pouranvari M, Amirabdollahian S, Abedi A, Goodarzi M: ‘Microstructure and failure behavior of dissimilar resistance spot welds between low carbon galvanized & austenitic stainless steels’, Mater. Sci. Eng. A, 2008, A480, 175–180.
   Web of Science ®Google Scholar
• Pouranvari M, Marashi SPH: ‘Similar and dissimilar RSW of low carbon and austenitic stainless steels: effect of weld microstructure and hardness profile on failure mode’, Mater. Sci. Technol., 2009, 25, 1411–1416.
   Web of Science ®Google Scholar
• Poggio S, Ponte M, Gambaro C, Adamowski J: ‘Resistance spot welding of advanced high strength steel DP600’, Proc. 1st Int. Conf. on ‘Super high strength steels’, Rome, Italy, November 2005, Association Italiana di Metallurgia, 1–13.
   Google Scholar
• Khan MS, Bhole SD, Chen DL, Biro E, Boudreau G, van Deventer J: ‘Welding behaviour, microstructure and mechanical properties of dissimilar resistance spot welds between galvannealed HSLA350 and DP600 steels’, Sci. Technol. Weld. Join., 2009, 14, 616–625.
   Web of Science ®Google Scholar
• ‘Specification for automotive weld quality resistance spot welding of steel’, D8·1M, AWS, New York, USA.
   Google Scholar
• Gould JE, Khurana SP, Li T: ‘Predictions of microstructures when welding automotive advanced high-strength steels’, Weld. J., 2006, 86, 111s–116s.
   Web of Science ®Google Scholar
• Pouranvari M, Asgari HR, Mosavizadeh SM, Marashi PH, Goodarzi M: ‘Effect of weld nugget size on overload failure mode of resistance spot weld’, Sci. Technol. Weld. Join., 2007, 12, 217–225.
   Web of Science ®Google Scholar
• Easterling KE: ‘Modelling the weld thermal cycle and transformation behavior in the heat-affected zone’, in ‘Mathematical modelling of weld phenomena’, (ed. , Cerjak H, Easterling K E); 1993, London, The Institute of Materials. Association Italiana di Metallurgia, 183–200.
   Google Scholar
• Pouranvari M, Marashi SPH: ‘Failure of resistance spot welds: tensile–shear versus coach–peel loading’, Ironmaking Steelmaking, 2012, 39, 104–111.
   Web of Science ®Google Scholar
• Goodarzi M, Marashi SPH, Pouranvari M: ‘Dependence of overload performance on weld attributes for resistance spot welded galvanized low carbon steel’, J. Mater. Process. Technol., 2009, 209, 4379–4384.
   Web of Science ®Google Scholar
• Zuniga SM: ‘Predicting overload pull-out failures in resistance spot welds’, PhD dissertation, Stanford University, Stanford, CA, USA, 1994.
   Google Scholar
• Pouranvari M: ‘Prediction of failure mode in AISI304 resistance spot welds’, Metalurgija: J. Metall., 2011, 17, 23–30.
   Google Scholar
• Pouranvari M, Marashi SPH: ‘Failure mode transition in AHSS resistance spot welds. Part I. Controlling factors’, Mater. Sci. Eng. A, 2011, A528, 8337–8343.
   Web of Science ®Google Scholar
• Pouranvari M, Marashi SPH, Safanama DS: ‘Failure mode transition in AHSS resistance spot welds. Part II. Experimental investigation and model validation’, Mater. Sci. Eng. A, 2011, A528, 8344–8352.
   Web of Science ®Google Scholar
• Pouranvari M: ‘Failure mode transition in similar and dissimilar resistance spot welds of HSLA420 and low carbon steels’, Can. Metall. Q., 2012, 51, 67–74.
   Web of Science ®Google Scholar
• Abadi MMH, Pouranvari M: ‘Correlation between macro/micro structure and mechanical properties of dissimilar resistance spot welds of AISI 304 austenitic stainless steel and AISI 1008 low carbon steel’, Metalurgija: J. Metall., 2010, 16, 133–146.
   Google Scholar