REFERENCES
- S. Guinard, O. Allix, D. Guedra-Degeorges and A. Vinet: ‘A 3D damage analysis of low-velocity impacts on laminated composites’, Compos. Sci Teehnol, 2002, 62, 585–589.
- A. J. Russell and C. P. Bowers: ‘Repairing delamination with low viscosity epoxy resins’, AGARD-CP-530-PAP-25, AGARD, Neuilly-sur-Seine, France, 1992.
- A. Ur-Rehman and P. F. Thomason: ‘Effects of artificial fatigue crack-closure on fatigue crack growth’, Fatigue Fraet. Eng. Mater. Struct. , 1993, 16, 1081–1090.
- R. Thévenin: ‘Composites @ Airbus — maintenance & repairs validations’, Proc. FAA Workshop for Composite damage tolerance and maintenance, Chicago, IL, USA, July 2006, NIAR.
- A. J. Fawcett and G. D. Oakes: ‘Boeing composite airframe damage tolerance and service experience’, Proc. FAA Workshop for Composite damage tolerance and maintenance, Chicago, IL, USA, July 2006, NIAR.6. R. Jones and R. J. Callinan: ‘A design study in crack patching’, Fibre Sci. Technol, 1981, 14, 99–111.
- Airbus: ‘Structural repair manual A330’, Technical Data Support and Services, Airbus, Toulouse, France, 2006.
- J. Paul and R. Jones: ‘Repair of impact damaged composites’, Eng. Fract. Mech. , 1992, 41, 127–141.
- J. Paul, R. A. Bartholomeusz, R. Jones and M. Ekstrom: ‘Bonded composite repair of cracked load-bearing holes’, Eng. Fract. Mech. , 1994, 48, 455–461.
- D. Tzetzis and P. J. Hogg: ‘Infield composites repair techniques for combat aircraft: research and development perspective’, Mater. Technol, 2007, 22, 2–9.
- V. K. Srivastava and D. Kumar: ‘Prediction of notched strength of laminated fibre composites under tensile loading conditions’, J. Compos. Mater. , 2002, 36, 1121–1133.
- J. Awerbuch and M. S. Madhukar: ‘Notched strength of composite laminates: predictions and experiments — a review’, J. Reinf Plast. Compos. , 1985, 4, 3–159.
- Hexcel Composite: IlexFlow® RTM 6 — product data', 2007, available at: http://www.hexcel.com/Products/Downloads/RTM% 20Data%20Sheets/
- F. Collombet, M. Mulle, Y.-H. Grunevald and R. Zitoune: 'Influence of thermoplastic phases and the associated process on fracture behaviour of UD carbon epoxy laminates: autoclave and RTM case studies', Proc. EUROMECH 473: Fracture of Composite Materials, Porto, Portugal, October 2005, University of Porto. S. A. Page, R. Mezzenga, L. Boogh, J. C. Berg and J. A. Manson: ‘Surface energetics evolution during processing of epoxy resins’, J. Colloid Interf Sci., 2000, 222, 55–62.
- S. A. Page, R. Mezzenga, L. Boogh, J. C. Berg and J. A. Manson:‘Surface energetics evolution during processing of epoxy resins’, J.Colloid Interf. Sci. , 2000, 222, 55–62.
- J. Wang: `Underfill of flip chip on organic substrate: viscosity, surface tension, and contact angle', Microelectron. Rehab. , 2002, 42, 293–299.
- K. Grundke, P. Uhlmann, T. Gietzelt, B. Redlich and H.-J. Jacobasch: ‘Studies on the wetting behaviour of polymer melts on solid surfaces using the Wilhelmy balance method’, Colloids Surf A, 1996, 116A, 93–104.
- P. Olivier, J. P. Cottu and B. Ferret: ‘Effects of cure cycle pressure and voids on some mechanical properties of carbon/epoxy laminates’, Composites, 1995, 26, 509–515.
- P. Prombut: `Caractérisation de la propagation de délaminage des stratifies composites multidirectionnels', PhD thesis, Université Paul Sabatier — Toulouse III, Toulouse, France, 2007.
- C. Marais and P. Sigety: `Tenacité des composites unidirectionnels en mode I', Proc. 22ième Journées Européennes des Composites (JEC 87), Paris, France, 1987, JEC.
- B. R. K. Blackman, A. J. Brunner and J. G. Williams: ‘Mode II fracture testing of composites: a new look at an old problem’, Eng. Fract. Mech. , 2006, 73, 2443–2455.