Al₂O₃ coatings fabricated on stainless steel/aluminium composites by microarc oxidation

References

• Yang X and Guo SJ: ‘Fe-Mo-B enhanced sintering of P/M 316L stainless steel’, J. Iron Steel Res. Int., 2008, 15, (1), 10–14.
   Web of Science ®Google Scholar
• Jagdhessh R, Sastikumar D, Kamachi U and Nath AK: ‘Laser processed metal–ceramic coatings on Aisitype 316l stainless steel’, Surf. Eng., 2004, 20, (5), 360–366.
   Web of Science ®Google Scholar
• Muthukumaran V, Selladurai V, Nandhakumar S and Senthilkumar M: ‘Experimental investigation on corrosion and hardness of ion implanted AlSi 316L stainless steel’, Mater. Des., 2010, 31, (6), 2813–2817.
   Web of Science ®Google Scholar
• Lu LH, Shen DJ, Zhang JW, Song J and Li L: ‘Evolution of micro-arc oxidation behaviors of the hot-dipping aluminum coatings on Q235 steel substrate’, Appl. Surf. Sci., 2011, 257, (9), 4144–4150.
   Web of Science ®Google Scholar
• Adraider Y, Pang YX, Nabhani F, Hodgson SN and Zhang ZY: ‘Laser-induced deposition of sol-gel alumina coating on stainless steel under wet condition’, Surf. Coat. Technol., 2011, 205, (23–24), 5345–5349.
   Web of Science ®Google Scholar
• Ibrahim A, Salem H and Sedky S: ‘Excimer laser surface treatment of plasma sprayed alumina-13% titania coatings’, Surf. Coat. Technol., 2009, 203, (23), 3579–3589.
   Web of Science ®Google Scholar
• Hou T and Zhang JZ: ‘Porous films on surface of titanium prepared by low voltage micro arc oxidation’, Surf. Eng., 2007, 23, (3), 169–172.
   Web of Science ®Google Scholar
• Krishna LR, Somaraju KRC and Sundararajan G: ‘The tribological performance of ultra-hard ceramic composite coatings obtained through micro arc oxidation’, Surf. Coat. Technol., 2003, 163–164, (30), 484–490.
   Web of Science ®Google Scholar
• Dunleavy CS, Golosnoy IO, Curran JA and Clyne TW: ‘Characterisation of discharge events during plasma electrolytic oxidation’, Surf. Coat. Technol., 2009, 203, (22), 3410–3419.
   Web of Science ®Google Scholar
• Lu LH, Zhang JW, Shen DJ, Wu LL, Jiang GR and Li L: ‘TEM analysis and wear resistance of the ceramic coatings on Q235 steel prepared by hybrid method of hot-dipping aluminum and plasma electrolytic oxidation’, J. Alloy Compd, 2012, 512, (1), 57–62.
   Web of Science ®Google Scholar
• Ashley DS and Anthony RI: ‘Effect of chemical milling on low-cycle fatigue behavior of an Al-Mg-Si alloy’, Corros. Sci., 2013, 68, 144–153.
   Web of Science ®Google Scholar
• Guo XH, Du KQ, Ge H, Guo QZ, Wang Y and Wang FH: ‘Good sensitivity and high stability of humidity sensor using micro-arc oxidation alumina film’, Electrochem. Commun., 2013, 28, 95–99.
   Web of Science ®Google Scholar
• Godja N, Kiss N, Löcker Ch, Schindel A, Gavrilovic A, Wosik J, Mann R, Wendrinsky J, Merstallinger A and Nauer GE: ‘Preparation and characterization of spark-anodized Al-alloy: Physical, chemical and tribological properties’, Tribol. Int., 2010, 43, (7), 1253–1261.
   Web of Science ®Google Scholar
• Raj V and Mubarakali M: ‘Formation of ceramic alumina nanocomposite coatings on aluminium for enhanced corrosion resistance’, J. Mate. Process Technol., 2009, 209, (12–13), 5341–5352.
   Web of Science ®Google Scholar
• Venugopal A, Panda R, Manwatkar S, Sreekumar K, Rama Krishna L and Sundararajan G: ‘Effect of micro arc oxidation treatment on localized corrosion behaviour of AA7075 aluminum alloy in 3·5% NaCl solution’, Trans. Nonferrous Met. Soc. China, 2012, 22, (3), 700–710.
   Web of Science ®Google Scholar
• Yang GL, Lü XY, Bai YZ, Cui HF and Jin ZS: ‘The effects of current density on the phase composition and microstructure properties of micro-arc oxidation coating’, J. Alloy Compd, 2002, 345, (1–2), 196–200.
   Web of Science ®Google Scholar
• Gnedenkov SV, Khrisanfova OA and Zavadnaya AG: ‘Compositon and adhesion of protective coatings on aluminum’, Surf. Coat. Technol., 2001, 145, (1–3), 146–151.
   Web of Science ®Google Scholar
• Román R, Cañadas I, Rodríguez J, Hernández MT and González M: ‘Solar sintering of alumina ceramics: Microstructural development’, Sol. Energy, 2008, 82, (10), 893–902.
   Web of Science ®Google Scholar
• Lahmar-Mebdoua Y, Vardelle A, Fauchais P and Gobin D: ‘Modelling the nucleation process in alumina lamellae deposited on a steel substrate’, Int. J. Therm. Sci., 2010, 49, (3), 522–528.
   Web of Science ®Google Scholar
• Aruna ST, Balaji N, Shedthi J and William Grios VK: ‘Effect of critical plasma spray parameters on the microstructure, microhardness and wear and corrosion resistance of plasma sprayed alumina coatings’, Surf. Coat. Technol., 2012, 208, (15), 92–100.
   Web of Science ®Google Scholar
• Ruhi G, Modi OP and Singh IB: ‘Corrosion behaviour of nano structured sol-gol alumina coated 9Cr-1Mo ferritic steel in chloride bearing environments’, Surf. Coat. Technol., 2009, 204, (3), 359–365.
   Web of Science ®Google Scholar
• Guo XZ, Tao J, Wang WT, Li HG and Wang C: ‘Effects of the inner mould material on the aluminium-316L stainless steel explosive clad pipe’, Mater. Design, 2013, 49, 116–122.
   Web of Science ®Google Scholar
• Puli R and Janakiram GD: ‘Corrosion performance of AiSi 316L friction surfaces coatings’, Corros. Sci., 2012, 62, 95–103.
   Web of Science ®Google Scholar
• Sun XJ, Tao J and Guo XZ: ‘Bonding properties of interface in Fe/Al clad tube prepared by explosive welding’, Trans. Nonferrous Met. Soc. China, 2011, 21, (10), 2175–2180.
   Web of Science ®Google Scholar