References
- Young DJ, Zhang J, Geers C and Shütze M: ‘Recent advances in understanding metal dusting: a review’, Mater. Corr., 2011, 62, 7–28.
- Szákalos P, Petterson R and Hertzman S: ‘An active corrosion mechanism for metal dusting on 304L stainless steel’, Corros. Sci., 2002, 44, 2253–2270.
- Alvino A, Lega D, Giacobbe F, Mazzocchi V and Rinaldi A: ‘Damage characterization in two reformer heating tubes after nearly 10 years of service at different operative and maintenance conditions’, Eng. Fail. Anal., 2010, 171, 526–1541.
- Ackermann H, Karduck P, Koehne H, Lucka K, Lucks L and von Richtofen A: ‘Metal dusting in low-NOx recirculation burners for fuel oil’, Corr. Eng. Sci. Technol., 2005, 40, (2), 233–238.
- Tawancy HM, Ul-Hamid A, Mohammed AI and Abbas NM: ‘Effect of materials selection and design on the performance of an engineering product – an example from petrochemical industry’, Mater. Des., 2007, 28, 686–703.
- Xie J, Cai H, Davies L, Sudlow I, Lane N and Oulton D: ‘Metal dusting in the low-point drains of crossover piping system in petrochemical environment’, Mater. Charact., 2010, 61, 145–153.
- Milwar GR, Evans HE, Aindow M and Mowforth CW: ‘The influence of oxide layers on the initiation of carbon deposition on stainless steel’, Oxid. Met., 2001, 56, 231–250.
- Uribe E, Salas O, Melo-Máximo D, Oseguera J, Lepienski CM, Torres RD and Souza RM: ‘Development of Al oxide PVD coatings against metal dusting’, Surf. Eng., to be published.
- Alvarez J, Melo D, Salas O, Reichelt R, Oseguera J and López V: ‘Role of Al oxide PVD coatings in the protection against metal dusting’, Surf. Coat. Technol., 2009, 204, (6–7), 779–783.
- Melo D, Sigüenza D, Salas O, Oseguera J, Reichelt R, López VM: ‘Production, characterization and evaluation of protective Cr oxide coatings against metal dusting’, Surf. Coat. Technol., 2009, 204, (6–7) 788–792.
- Melo-Máximo L, Salas O, Melo-Máximo D, Oseguera J, López-Hirata VM, Torres RD, Lepienski CM and Souza RM: ‘Performance of Cr oxide coatings on 304 steel against metal dusting’, Surf. Coat. Technol., 2013, 237, 39–50.
- Sarakinos K, Alami J and Kostantinidis S: ‘High power pulsed magnetron sputtering: a review on scientific and engineering state of the art’, Surf. Coat. Technol., 2010, 204, 1661–1684.
- Lin J, Moore JJ, Sproul WD, Mishra B, Rees JA, Wu Z, Chistyakov R and Abraham B: ‘Ion energy and mass distributions of the plasma during modulated pulse power magnetron sputtering’, Surf. Coat. Technol., 2009, 203, 3676–3685.
- Lin J, Moore JJ, Sproul WD, Mishra B, Wu Z and Wu J: ‘The structure and properties of chromium nitride coatings deposited using dc, pulsed dc and modulated pulse power magnetron sputtering’, Surf. Coat. Technol., 2010, 204, 2230–2239.
- Windischmann H: ‘Intrinsic stress in sputter-deposited thin films’, Crit. Rev. Solid State Mater. Sci., 1992, 17, (6), 547–596.
- Bull SJ: ‘Failure mode maps in the thin film scratch adhesion test’, Tribol. Int., 1997, 30, (7), 491–498.
- Gaskell DR: ‘Introduction to metallurgical thermodynamics’, 2nd edn, Chap. 10, ‘Reactions involving pure condensed phases and gaseous phase’, 272–280; 1981, New York, McGraw-Hill.
- Gheno T, Monceau D and Young D: ‘Mechanism of breakaway oxidation of Fe–Cr and Fe–Cr–Ni alloys in dry and wet carbon dioxide’, Corros. Sci., 2012, 64, 222–233.
- Thouless M: ‘Some mechanics for the adhesion of thin films’, Thin Solid Films, 1989, 181, 397–406.
- Sabioni ACS, Huntz AM, Silva F and Jomard F: ‘Diffusion of iron in Cr2O3: polycrystals and thin films’, Mater. Sci. Eng. A, 2005, A392, 254–261.