9
Views
11
CrossRef citations to date
0
Altmetric
Technical Paper

Particle Exhaust Characteristics of an In-Vessel Cryopump Used in DIII-D Diverted Plasmas

, , , , , , , , , , , , , & show all
Pages 355-363 | Published online: 09 May 2017

References

  • M. A. MAHDAVI et al., “The DIII-D Collaborative Advanced Divertor Program,” GA-A19547, General Atomics (Feb. 1989).
  • M. M. MENON and P. K. MIODUSZEWSKI, “Particle Exhaust Schemes in the DIII-D Advanced Divertor Configuration,” Proc. 13th Symp. Fusion Engineering, Knoxville, Tennessee, October 2–6, 1989, Vol. 1, p. 542, Institute of Electrical and Electronics Engineers (1990).
  • M. M. MENON et al., “Particle Exhaust Scheme Using an In-Vessel Cryocondensation Pump in the Advanced Divertor Configuration of the DIII-D Tokamak,” Fusion Technol., 22, 356 (1992).
  • M. J. SCHAFFER, Private Communication.
  • M. M. MENON, M. J. SCHAFFER, and A. KELLMAN, “Voltage Transients Induced by Plasma Disruptions in the DIII-D Tokamak,” Bull. Am. Phys. Soc., 37, 1570 (1992).
  • G. J. LAUGHON, K. M. SCHAUBEL, C. B. BAXI, G. L. CAMPBELL, M. A. MAHDAVI, C. C. MAKARIOU, and M. M. MENON, “Two Phase Liquid Helium Flow Testing to Simulate Operation of a Cryocondensation Pump in the DIII-D Tokamak,” presented at the 15th Int. Cryogenic Engineering Conf. Industrial Exhibition, Genova, Italy, June 7–10, 1994.
  • F. LLEWELLYN-JONES, Ionization Avalanches and Breakdown, Methuen, London (1967).
  • E. E. REIS et al., “Design and Analysis of a Cryopump for the DIII-D Advanced Divertor,” Proc. 17th Symp. Fusion Technology, Rome, Italy, September 14–18, 1992, Elsevier (1993).
  • P. K. MIODUSZEWSKI, L. W. OWEN, M. M. MENON, and J. H. HOGAN, “Particle Exhaust Modeling in the Collaborative DIII-D Advanced Divertor Program,” J. Nucl. Mater., 176, 733 (1990).
  • D. HEIFETZ, D. POST, M. PETRAVIC, J. WEISHEIT, and G. BATEMAN, “A Monte-Carlo Model of Neutral Particle Transport in Diverted Plasmas,” J. Comput. Phys., 46, 309 (1982).
  • J. P. SMITH et al., “Installation and Initial Operation of the DIII-D Advanced Divertor Cryocondensation Pump,” Proc. 15th Symp. Fusion Engineering, Hyannis, Massachusetts, October 11–15, 1994, Institute of Electrical and Electronic Engineers, GA-A21396, General Atomics (1993).
  • K. SCHAUBEL et al., “Development of an In-Vessel Cryopump System for the DIII-D Tokamak,” presented at Cryogenic Engineering Conf., Albuquerque, New Mexico, July 12–16, 1993; Advances in Cryogenic Engineering, Vol. 398, p. 1983, Plenum Press, New York (1993).
  • K. SCHAUBEL, “Design of the Advanced Divertor Pump Cryogenic System for DIII-D,” Proc. 14th Symp. Fusion Engineering, San Diego, California, September 30–October 3, 1991, Vol. 2, p. 1222, Institute of Electrical and Electronic Engineers (1992).
  • C. C. KLEPPER et al., “Divertor Neutral Pressure Enhancement,” Nucl. Fusion, 33, 533 (1993).
  • R. MAINGI et al., “Effect of Particle Exhaust on SOL and Divertor Plasma Parameters in DIII-D,” Bull. Am. Phys. Soc., 38, 2059 (1993).
  • M. J. SCHAFFER et al., “Impurity Localization During Strong Gas Puffing and Divertor Pumping on DIII-D,” Bull. Am. Phys. Soc., 38, 2058 (1993).
  • M. A. MAHDAVI et al., “Active Density Control in DIII-D H-Mode Plasmas,” Proc 20th Conf. Controlled Fusion and Plasma Physics, Lisbon, Portugal, July 26–30, 1993, European Physical Society.
  • D. L. HILLIS et al., “Helium Transport and Exhaust Studies of H-Mode Discharges in the DIII-D Tokamak,” Plasma Phys. Control. Fusion (to be published).
  • M. R. WADE et al., “Helium Exhaust Studies in ELM-ing H-Mode Discharges in the DIII-D Tokamak Using an Argon-Frosted Divertor Cryopump,” Phys. Rev. Lett., (submitted for publication).

Reprints and Corporate Permissions

Please note: Selecting permissions does not provide access to the full text of the article, please see our help page How do I view content?

To request a reprint or corporate permissions for this article, please click on the relevant link below:

Academic Permissions

Please note: Selecting permissions does not provide access to the full text of the article, please see our help page How do I view content?

Obtain permissions instantly via Rightslink by clicking on the button below:

If you are unable to obtain permissions via Rightslink, please complete and submit this Permissions form. For more information, please visit our Permissions help page.